INSTRUCTIONS FOR:
INDUSTRIAL FAN HEATERS
Output 5kW, 9kW, 15kW,
MODEL No: EH5001, EH9001, EH15001
1.2. GENERAL SAFETY
1.2.1. MAINTENANCE PRECAUTIONS
WARNING! Disconnect the heater from the mains power
supply, before servicing or performing any maintenance.
Servicing or maintenance must only be carried out by an
authorised service agent.
Check that the heater is in sound condition and good working
order. Take immediate action to repair or replace damaged
parts.
Use recommended parts only. Unapproved parts may be
dangerous and will invalidate the warranty.
DO NOT attempt to repair a damaged heater, contact an
authorised service agent.
1.2.2. POSITIONING OF HEATER
WARNING! DO NOT use the heater near ammable material,
liquids, solids, gases or compressed gas cylinders etc.
DO NOT place the heater close to a bath, wash basin, shower,
swimming pool or any other water-filled area or wet surface.
DO NOT place the heater up against any surface such as a
wall, door or furniture etc.
DO NOT place the heater immediately below any electrical
outlet.
Position the heater at least a minimum of 0.5mtr at the rear
and sides, and 2mtr at the front, from any walls or objects.
DO NOT place the heater on a raised surface or anywhere
where it could topple over.
Original Language Version
EH15001, EH9001, EH5001 Issue: 5(L) - 11/06/14
1.1. ELECTRICAL SAFETY
WARNING! ELECTRICAL INSTALLATION OF THE HEATER
TO A 3-PHASE 415VOLT SUPPLY MUST ONLY BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Make sure the power supply cable is correctly connected
to the earth. It is the user’s responsibility to read,
understand and comply with the following:
You must check all electrical equipment and appliances to
ensure they are safe before using. You must inspect power
supply leads, plugs and all electrical connections for wear and
damage. You must ensure the risk of electric shock is
minimised by the installation of appropriate safety devices. An
RCCB (Residual Current Circuit Breaker) should be
incorporated in the main distribution board. You must also read
and understand the following instructions concerning electrical
safety.
1.1.1. The Electricity At Work Act 1989 requires all portable
electrical appliances, if used on business premises, to be tested
by a qualified electrician, using a Portable Appliance Tester
(PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of
electrical appliances responsible for the safe condition of the
appliance and the safety of the appliance operator. If in any
doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure insulation on all cables and the product itself is safe
before connecting to mains power supply.
1.1.4. Ensure that cables are always protected against short circuit
and overload.
1.1.5. Regularly inspect power
supply, leads, plugs and all
electrical connections for
wear and damage,
especially power
connections, to ensure that
none are loose.
1.1.6. Important: Ensure the
voltage marked on the
product is the same as the
electrical power supply to
be used. A three phase
plug must be fitted to this
machine.
1.1.7. DO NOT pull the powered appliance by the power cable.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections.
Immediately replace or have repaired by a qualified electrician.
1.1.10. This product must be fitted with a 3-phase plug according
to the diagram, and will require a minimum of, 16Amps
per phase for EH5001 and EH9001, and 32Amps for
EH15001, of electrical supply. You must contact a qualified
electrician to ensure an appropriately fused supply is
available. Connect GREEN/YELLOW wire to earth (E)
terminal . Connect the live wires to live 1, 2 and 3.
When completed, check that there are no bare wires, that all
wires have been connected correctly, that the cable external
insulation extends beyond the cable restraint and that the
restraint is tight.
EH5001 EH9001
© Jack Sealey Limited
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
To Next Page
Need help?
General
