Sealey FCR500 - User Manual

To Next Page

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

 WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that may

occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the

operator.

9 Read unpacking instructions Section 4 below before removing ramps from packaging.

8 DO NOT overload ramps, maximum capacity single = 250kg, pair = 500kg. All loads must be evenly distributed.

9 Always use the safety chain to securely fasten the ramp to the vehicle to prevent the ramp slipping off the tailgate.

9 Carefully roll or winch equipment up or down the ramp. Never drive or ride your equipment while loading or unloading.

9 Make sure the ramp is aligned with the wheels of the equipment being loaded or unloaded.

9 Always load or unload on a solid, level, well lit and stable surface with the vehicle in gear the parking/emergency brake on and the engine

off.

9 Wear gloves. Remove ill tting clothing, remove ties, watches, rings and other loose jewellery and contain long hair.

9 Maintain correct balance and footing, do not over reach. Ensure the oor is not slippery and wear non-slip shoes.

9 Keep children and unauthorised persons away from the work area.

9 Use as a loading ramp only.

9 Ramp surfaces must be clean, dry and free from oil, grease and water.

9 Maximum height of the tailgate that the ramp attaches to is 76cm.

9 Inspect ramp before each use. Check fasteners for tightness, replace any worn or damaged parts.

8 DO NOT attempt to use a ramp that is damaged in any way.

8 DO NOT modify the ramp in any way.

9 Proper care and maintenance of the ramp is critical to safety.

9 Proper use of this product is critical to safety. Improper use may result in personal or property damage which is not covered by the

warranty.

2. INTRODUCTION

Manufactured from strong, durable powder coated steel. Provides safe and easy ramp access for in-line and multi axle vehicles. Suitable for

loading/unloading motorbikes, quads, ride-on lawnmowers and mini tractors from vans or trailers. Features a chain and hook to help secure

ramps while in use. Folding design allows compact storage when not in use.

3. SPECIFICATION

Model no: .................................................................FCR500

Folded dimensions L x W x H: ................. 890 x 230 x 150mm

Extended dimensions L x W x H: .............2000 x 230 x 50mm

Maximum capacity single/pair: .............................. 250/500kg

Weight single/pair: ............................................... 13.5/27.5kg

Maximum height of tailgate from ground: ...................... 76cm

4. UNPACKING RAMPS

4.1. Carefully lift one ramp at a time using handle.

4.2. Set ramp on a at surface. Note: arrow indicates which side is up.

4.3. Release handle by sliding it upwards.

4.4. Unfold top section of ramp, then the other section of ramp.

4.5. Remove the stopper and angle ramp from within.

Wear protective

gloves

Refer to

Instruction

Manual

STEEL FOLDING LOADING RAMPS 500KG

CAPACITY PER PAIR

MODEL NO: FCR500

FCR500 Issue 2(1,2,5) 13/09/21

Original Language Version

Other manuals for Sealey FCR500

Instructions2 pages

Need help?

Do you have a question about the Sealey FCR500 and is the answer not in the manual?

Summary

The Sealey FCR500 Steel Folding Loading Ramps are designed to provide safe and easy access for loading and unloading vehicles such as motorbikes, quads, ride-on lawnmowers, and mini tractors from vans or trailers. Manufactured from strong, durable powder-coated steel, these ramps are built to a high standard, ensuring years of trouble-free performance when used and maintained correctly.

Function Description:

The primary function of these ramps is to create a secure incline for moving wheeled equipment onto or off a raised platform, such as a vehicle tailgate or trailer. Each ramp features a chain and hook mechanism to securely fasten it to the vehicle, preventing slippage during use. The folding design allows for compact storage when not in use, making them convenient for transport and storage. The ramps are designed for in-line and multi-axle vehicles, accommodating a variety of equipment types.

Important Technical Specifications:

Model Number: FCR500
Folded Dimensions (L x W x H): 890 x 230 x 150mm
Extended Dimensions (L x W x H): 2000 x 230 x 50mm
Maximum Capacity (Single/Pair): 250kg / 500kg (Note: All loads must be evenly distributed.)
Weight (Single/Pair): 13.5kg / 27.5kg
Maximum Height of Tailgate from Ground: 76cm (beyond this height, the incline will be too steep)
Material: Strong, durable powder-coated steel.

Usage Features:

Safety First: Users are strongly cautioned to read all instructions carefully before use. Key safety measures include:
- Always use the safety chain to securely fasten the ramp to the vehicle tailgate.
- DO NOT overload the ramps; adhere strictly to the 250kg single / 500kg pair capacity.
- Ensure the ramp is aligned with the equipment's wheels.
- Load/unload on a solid, level, well-lit, and stable surface with the vehicle in gear, parking/emergency brake on, and engine off.
- Never drive or ride equipment while loading or unloading.
- Wear protective gloves and appropriate non-slip footwear. Remove loose clothing, ties, watches, rings, and other jewellery.
- Maintain correct balance and footing; do not overreach.
- Keep children and unauthorized persons away from the work area.
- Ramp surfaces must be clean, dry, and free from oil, grease, and water.
Unpacking and Setup:
1. Carefully lift one ramp at a time using its handle.
2. Set the ramp on a flat surface, noting the arrow indicating the "up" side.
3. Release the handle by sliding it upwards.
4. Unfold the top section, then the other section of the ramp.
5. Remove the stopper and angle the ramp from within.
6. Place the lip edge of the ramp against the vehicle's tailgate (maximum 76cm height).
7. Secure the ramp to the vehicle using the chain and test by pulling backwards to ensure it doesn't slide.
8. Once secure, position the equipment behind the ramps, centering it between the rails.
9. Carefully roll or winch the equipment up/down, ensuring the ramp sustains the load without bowing.
Storage: The folding design allows for compact storage. After use, unhook the chain, fold the ramp, and store it in a clean, dry, and childproof environment.

Maintenance Features:

Regular Inspection: Inspect the ramp before each use. Check fasteners for tightness and replace any worn or damaged parts immediately.
Damage Prevention: DO NOT attempt to use a ramp that is damaged in any way. DO NOT modify the ramp.
Cleaning: Keep ramp surfaces clean, dry, and free from oil, grease, and water to ensure optimal grip and safety.
Proper Care: Proper care and maintenance are critical for safety and extending the product's lifespan. Improper use or lack of maintenance may result in personal or property damage not covered by the warranty.
Environmental Protection: Unwanted materials, packaging, and the product itself should be recycled responsibly. Dispose of fluids (if applicable) and the product according to local regulations when it becomes unserviceable.

The Sealey FCR500 ramps are a robust and practical solution for anyone needing to load or unload wheeled equipment, emphasizing safety and durability through proper use and maintenance.

Sealey FCR500 Specifications

General

Brand	Sealey
Model	FCR500
Category	Lifting Systems
Language	English

Sealey FCR500 - User Manual

Other manuals for Sealey FCR500

Summary

Safety Precautions

Introduction to Loading Ramps

Product Specifications

Unpacking Instructions

Operation Guide

Summary

Safety Precautions

Introduction to Loading Ramps

Product Specifications

Unpacking Instructions

Operation Guide

Overview

Function Description:

Important Technical Specifications:

Usage Features:

Maintenance Features:

Sealey FCR500 Specifications