Sealey LFT03 User Manual

INSTRUCTIONS FOR:
ALUMINIUM LOFT LADDER
Model No.: LFT03
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPOR
TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTL
Y AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1 GENERAL SAFETY
p WARNING! Ensure Health and Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
3 Familiarise yourself with the application and limitations of the ladder, as well as the potential hazards.
3 Maintain the equipment in good condition.
3 Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
3 Keep the work area clean, uncluttered and ensure there is adequate lighting.
p WARNING! Rest the base of the ladder on level and solid ground.
p WARNING! Never over-reach when on the ladder.
3 Keep children and unauthorised persons away from the working area.
7 DO NOT use the ladder for any purpose other than that for which it was designed.
7 DO NOT use the equipment if any parts are damaged or missing as this may cause failure and/or personal injury.
7 DO NOT allow children to climb the ladder.
7 DO NOT use the equipment when you are tired, under the influence of alcohol, drugs or intoxicating medication.
3 When not in use, stow securely.
2. INTRODUCTION
Aluminium loft ladder manufactured to BS7553:1992 class G. Complete with hand rail and all fixings with factory assembled components for
quick and easy installation. 3-Section design enables ladder to fit in smaller areas than standard 2-section ladders.
3. CONTENTS & SPECIFICATION
A
B
C
D
G
E
H
F
L
I
K
J
3.1 Contents:
Included with the ladder you should find:
A 3 x washers
B 6 x screws (31mm)
C 2 x nuts
D 2 x screws (64mm)
E 8 x screws (15mm)
F 2 x screws (18mm)
G Pole (for opening trap door and lowering ladder)
H Hand-rail
I Fixing pins/screws and marker for auto latch
J Trap door hinges
K Auto latch
L Stabilisers/retainers for hand rail
3.2 Specification:
No. of sections 3
Max floor to floor 3m (see fig )
Min loft clearance 1050mm
Min loft opening 432 x 508mm
Max load 100kg (15.7 stone)
3m (max)
fig 1
LFT03 - 1 - 130104

Sealey LFT03 Specifications

General

Brand	Sealey
Model	LFT03
Category	Ladders
Language	English

Summary

Safety Instructions

General Safety

General safety rules and precautions for using the equipment, including hazard awareness and maintenance.

Introduction

Contents and Specification

Contents

List of all components included with the aluminium loft ladder for installation and use.

Specification

Technical details of the loft ladder, including number of sections, dimensions, and maximum load capacity.

Installation and Use

Loft Opening Preparation

Instructions for preparing the loft opening, ensuring the trap door is hinged correctly for the ladder.

Ladder Guide Assembly Installation

Steps for fitting the ladder guide assembly to the loft frame, ensuring correct bracket positioning.

Ladder Positioning and Catch Engagement

Guidance on lowering the ladder, engaging catches, and checking the angle indicator for safe use.

Guide Assembly Stops Adjustment

Procedure for adjusting the guide assembly stops to accommodate varying floor-to-floor heights.

Pivot Arm Fixing to Floor

Instructions for securing the pivot arm to the loft floor when the ladder is in the climbing position.

Securing Ladder in Stowed Position

Steps for pushing the ladder back up and ensuring sections are closed and catches are locked.

Handrail Attachment

Details on how to attach the handrail to the middle or top section of the ladder.

Using the Lowering/Raising Pole

Instructions on how to use the provided pole to safely lower and raise the loft ladder.

Auto-Latch Fitting and Adjustment

Procedure for fitting, positioning, and testing the auto-latch mechanism for the trap door.

Maintenance

Cleaning and Drying Procedure

Guidelines for keeping the ladder clean and dry, free from dirt, grease, and liquids.

Pre-Use Rung Inspection

Ensuring rungs are free from hazardous materials before each use for safety.

Guide Assembly Lubrication and Movement Check

Maintenance steps for ensuring the guide assembly is well lubricated and moves freely.

Damage and Wear Inspection

Instructions for thorough checks for damage or wear before and after each use, and actions to take if found.