Sealey ms155 - User Manual

INSTRUCTIONS FOR
VACUUM OIL & FLUID EXTRACTOR MANUAL 1.6LTR
MODEL NO: MS155
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
99 9Keep the extractor clean and maintain it in good condition (use an authorised service agent).
9 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9 Keep all non-essential persons away from the work area.
99 9Check extractor connections and fittings before use.
99 9Ensure that the tank capacity exceeds the amount of fluid to be collected.
98 9DO NOT use the extractor for any purpose other than that for which it is designed.
99 9DO NOT operate the extractor if any parts are damaged or missing as this may cause failure and/or personal injury.
9 9WARNING! Engine oil maybe hot when extracting.
▲ ImpoRtANt! Ensure that you wear protective clothing, gloves, goggles, face mask as appropriate for the fluid being extracted.
9 9WARNING! Do Not allow uncontrolled discharge of fluids thus polluting the environment.
9 Dispose of waste fluids in accordance with local authority regulations.
9 9WARNING! Do Not use with gasoline or other flammable liquids.
98 9DO NOT use the unit to extract dangerous chemicals, poisons, acids, alkalines or solvents.
98 9The container is not designed for long term storage.
98 9DO NOT store the unit under extreme conditions.
98 9DO NOT turn the container upside down when it is holding fluids.
98 9DO NOT adapt the unit for any other purpose.
98 9When not in use, store in a safe, dry, childproof area.
2. INTRODUCTION
1.6 lt capacity, constructed from composite materials, suitable for the extraction of engine or transmission oils from cars, motorcycles, marine
engines, stationary engines and industrial machinery. Also suitable for low viscosity uids such as water. Supplied with two suction probes
and cover cap. Use probes to remove engine oil through the dipstick tube.
3. SPECIFICATIONS
Model no: ...................................................................MS155
Capacity: ........................................................................ 1.6ltr
Suction probes: ............Ø8mm x 1300mm, Ø5mm x 1008mm
Fig.1
MS155| Issue 1 22/07/15
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual

Summary

Safety Instructions

Introduction to Vacuum Oil Extractor

Product Specifications

Assembly Procedure

Pump and Adaptor Attachment

Screw the siphon pump onto the container's threaded fitting and push the universal adaptor into the container top.

Probe Insertion

Push the required suction probe into the inlet hole of the universal adaptor until tight.

Operating the Extractor

Pre-Operation Checks

Ensure the machine is stopped and secured, and be aware of hot fluids before starting extraction.

Fluid Extraction Process

Feed probe, ensure immersion, pump handle to create vacuum, and monitor fluid level to avoid pump damage.

Transport and Emptying

Seal container with cap for transport, remove adaptor to pour away contents.

Maintenance and Storage

Cleaning and Drying

Clean the unit and probes with warm, soapy water and dry thoroughly before storage.

Damage Checks and Storage

Regularly check for damage, replace parts as needed, and store in a safe, dry location.

Sealey ms155 Specifications

General

Model	MS155
Material	Stainless Steel
Width	600mm
Number of Motors	1
Voltage	230V
Frequency	50Hz
Filter Type	Aluminium Grease Filter