Sealey SA792 - User Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered
to when using this equipment.
 WARNING!Disconnect from air supply before refilling with nails/staples, servicing or performing maintenance.
 Maintain the nail/staple gun in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and
will invalidate the warranty.
 Use in suitable clean and tidy work area, free from unrelated materials. Ensure there is adequate lighting.
 WARNING! Always wear approved eye and/or face and hand protection when operating the nail/staple gun.
 Remove ill fitting clothing. Remove ties, loose jewellery, and contain and/or tie back long hair.
 Keep hands and body clear of working parts.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the working area.
 Check moving parts alignment on a regular basis.
 Ensure workpiece is secure before operating the nail/staple gun. Never hold a workpiece by hand.
 When the nail/staple gun is put down during pauses in operation ensure that the trigger catch slide is not
depressed by the weight of the nail/staple gun or by placing the nail/staple gun in a restricted position that
could put pressure on the trigger catch slide.
 During extended breaks in operation disconnect the nail/staple gun from the air supply.
 WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 60-100psi.
 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
 Prolonged exposure to vibration from this nail/staple gun may pose a health risk. It is the owner’s
responsibility to correctly assess the potential hazard and issue guidelines for safe periods of use and offer
suitable protective equipment.
 DO NOT use any power source except an air compressor.
 DO NOT operate the nail/staple gun near any flammable substance or on any container that once
contained an flammable substance.
 DO NOT use the nail/staple gun for a task it is not designed to perform.
 DO NOT operate nail/staple gun if any parts are damaged or missing as this may cause failure and/or personal injury.
 DO NOT carry the nail/staple gun by the hose, or yank the hose from the air supply.
 DO NOT place the nail/staple gun close to your face and do not point at other persons or animals.
 DO NOT operate nail/staple gun when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT carry the nail/staple gun with your finger on the trigger.
 DO NOT direct air from the air hose at yourself or others.
 When not in use, disconnect from air supply and store in a safe, dry, childproof location.
INSTRUCTIONS FOR:
AIR OPERATED
NAIL/STAPLE GUN
MODEL No: SA792
Original Language Version
SA792 Issue: 2 - 13/11/09

Summary

Safety Instructions

General Safety Precautions

Covers safe work environment, personal attire, secure operation, and equipment placement.

Operational Warnings and Prohibitions

Highlights critical warnings, air pressure limits, vibration risks, and prohibited uses to prevent injury.

Introduction and Specification

Preparing Gun for Use

Air Supply

Details required air pressure, draining the tank, and air inlet filter cleaning.

Couplings

Explains the use of leader hoses and quick-release couplings to prevent vibration-induced failure.

Operating Instructions

Loading the Magazine

Instructions on how to open, load nails/staples, and close the magazine.

Connecting Air and Firing

Details on connecting air supply, understanding the trigger mechanism, and firing the gun.

Clearing Blockages

Steps to follow when a nail or staple becomes jammed in the mechanism.

Maintenance

General Maintenance

Covers cleaning, lubrication, and addressing power loss issues.

Bolt Security and Servicing

Checking hex bolt security and contacting service agents for full maintenance.

Sealey SA792 Specifications

General

Model No	SA792
Nail Length	15-50mm
Thread Size	1/4" BSP
Magazine Capacity	100
Nail Capacity	100
Nail Type	Brad Nails
Working Pressure	70-120 PSI