Sears WB44K5013 - User Manual

INSTALLATION INSTRUCTIONS FOR YOUR NEW
24" BUILT-INOVEN
Before you begin - Read these instructions completely and carefully.
IMPORTANT - Save these instructions for local inspector's use.
IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer - Be sure to leave these instructions with the Consumer.
Note to Consumer - Keep these instructions with your Use and Care Book for future
reference.
Be sure your oven is installed properly by a qualified
installer or service technician.
• Be sure the oven is securely installed in a cabinet
that is firmly attached to the house structure.
Weight on the oven door could cause the oven to
tip resulting in serious personal injury or death.
Never allow anyone to climb, sit, lean, stand, or
hang on the oven door.
• The wall coverings, countertop and cabinets
around the oven should be able to withstand the
heat (up to 200°F) generated by the oven.
1/8" Drill Bit
Electric or Hand Drill
Flat Blade screwdriver
Ruler
Ha nd or saber saw
Pencil
Cabinet space must be provided to enclose the
recessed partofyour built-in oven. SINGLE OVEN
IN STALLATI ON i See Figure I for all necessary
dimensions. DOU BLE OVEN INSTALLATION
i See Figure 2 for all necessa_j dimensions. It is
best to make a template to insure accurate cutting.
Place the bottom of the template on a level base line,
above the floor. See dimension E in Figure I (Single
Oven) or Figure 2 (Double Oven).
It is important that the oven be installed at or above
the minimum height specified. The unit has been
tested and approved, in accordance with safety
standards, at this height.
Pub. No, 31-10241
INT224-14
CAUTION: The electrical power to
the oven supply line must be shut
off while connections are being
made. Failure to do so could result
in serious injury or death.
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse having
amperage as noted on rating plate. (Rating plate
is located on oven frame.)
We recommend you have the electrical wiring and
hookup of your oven done by a qualified electrician.
After installation, have the electrician show you
where your main range disconnect is located.
Check with your local utilities for electrical codes
which apply in yourarea. Failuretowireyour range
according to governing codes could result in a
hazardous condition. If there are no local codes,
your range must be wired and fused to meet the
requirements of the National Electrical Code, ANSI/
NFPA No. 70-Latest Edition. You can geta copyof
the National Electrical Code, ANSI/NFPA NO. 70-
Latest Edition by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National Electrical
Code requires that new, but not existing,
construction utilize a 4 conductor connection to an
electric range. When installing an electric range in
new construction, follow the instructions in NEW
CONSTRUCTION AND FOUR-WIRE CORD
CONNECTION KIT.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 120/240 Volt, 60 Hertz electrical
system. If you connect to aluminum wiring, properly
installed connections approved for use with
aluminum wiring must be used.

Summary

Installation Safety and Electrical Requirements

For Your Safety

Ensure qualified installation, secure cabinet mounting, and heat-resistant surroundings to prevent hazards.

Electrical Installation Guidelines

Follow proper voltage, grounding, circuit protection, and electrical codes for safe appliance connection.

Cabinet Opening Preparation and Dimensions

Single Oven Installation

Details dimensions and preparation for installing a single built-in oven, including cutout and support requirements.

Double Oven Installation

Provides dimensions and preparation steps for installing a double built-in oven, specifying cutout and support needs.

Electrical Connection Procedures

Three Conductor Branch Circuit Connection

Instructions for connecting the oven using a three-wire circuit, including wire color matching and neutral grounding.

New Construction Four Conductor Connection

Guides connecting the oven in new builds or mobile homes using a four-wire circuit, emphasizing grounding and neutral separation.

Oven Installation and Door Handling

Installing the Oven

Steps for placing the oven into the cabinet, drilling holes, and securing it with screws.

Removing and Replacing the Oven Door

Detailed instructions on how to safely remove and reattach the oven door, including hinge care.

Sears WB44K5013 Specifications

General

Brand	Sears
Model	WB44K5013
Category	Oven
Language	English