SECO-LARM SD-996C-NUQ - User Manual

8 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Manual

SD-996C-NUQ

Universal Door Strike

 Reversible non-handed design fits either right-

hand or left-hand doors

 Low profile: Strike is only 1

1

/

4

" deep for use with

aluminum frames

 The SD-996C-NUQ is intended to be used with U

L

Listed Exit Hardware

 The SD-996C-NUQ shall not impair the intended

operation of an emergency unit

 The SD-996C-NUQ shall not impair the operation

of panic hardware mounted on the door

 Wiring methods shall be in accordance

with NFPA70

 Optional lip-extension brackets available:

- SD-995C-LE25 1" Lip Extension

- SD-995C-LE50 2" Lip Extension

 Field selectable for fail-safe or fail-secure

 12/24 VDC Operating voltage

 Static strength – 1,000-lb (4,448N)

 Dynamic strength – 50ft-lb (68J)

 Includes wiring harness and connectors

for either 12VDC or 24VDC

 Trim plate included

 Mounting tabs included for mounting to

hollow aluminum door

 For Indoor Use Only

 Includes 3 faceplates for nearl

y

an

y

type of door:

 Aluminum door frames

 Hollow metal door frames

 Wood door frames

43RG

Features:

Questions and Answers

S
Sarah PhillipsJul 27, 2025
What to do if SECO-LARM door locks electric strike does not activate?
- T
  Terry WongJul 28, 2025
  If your SECO-LARM door lock's electric strike isn't activating, start by dismounting the strike and ensuring the wiring connector is properly connected. Verify that the wiring connector is connected to a 12 or 24VDC power source. Use a multimeter to check if the strike is receiving the correct voltage and amperage; if not, consider using heavier gauge wires or increasing the power supply output. Also, confirm that the activation device, such as a keypad or push-button switch, is functioning correctly. Check the door latch for proper operation and replace it if needed. Finally, the electric strike's position may require adjustment by moving it or adding washers or shims.
D
Derek GreeneAug 13, 2025
Why does my SECO-LARM SD-996C-NUQ strike make a buzzing sound?
- B
  Bobby AdamsAug 13, 2025
  If your SECO-LARM door lock strike is making a buzzing sound, use a DC power supply instead of an AC power supply.

Summary

Product Features

Product Introduction and Specifications

Introduction

Brief overview of the product's versatility and configuration for different door types.

Specifications

Details operating voltage, current, temperature, strength, and endurance ratings.

Parts List

Itemizes all components included with the electric door strike for installation.

Installation Guide

Measuring and Template Mounting

How to measure critical lines and apply the stick-on template to the door frame.

Door Frame Preparation and Strike Mounting

Steps for preparing the frame, mounting tabs, trim plate, and configuring strike operation.

Sample Installations

Aluminum Door Frame Installation

Detailed steps and diagrams for installing the strike on aluminum frames.

Hollow Metal Door Frame Installation

Detailed steps and diagrams for installing the strike on hollow metal frames.

Wood Door Frame Installation

Detailed steps and diagrams for installing the strike on wooden frames.

Wiring and Troubleshooting

Wiring Diagram

Illustrations and instructions for connecting the strike to 12VDC or 24VDC power.

Troubleshooting Guide

Solutions for common issues like the strike not activating or the door not opening.

SECO-LARM SD-996C-NUQ Specifications

General

Type	Electromagnetic Lock
Voltage	12/24 VDC
Current Draw	500mA@12VDC, 250mA@24VDC
Finish	Stainless steel
Fail Safe/Fail Secure	Fail Safe
Door Gap	1/8" (3mm)