Sega SuperBooth User Manual

UnPacking Procedures
1. Use scissors or utility knife to cut* through the
strapping plastic. *Do not cut too deep or you’ll damage unit.
2. Open the cardboard box.
3. Remove back and middle wall from the pallet.
4. Remove the main SuperBooth pod from the pallet with
a forklift or roll the pod off the pallet with a ramp.
5. Place SuperBooth pod [A] in desired location [total area
of fully assembled booth is 125” Wide x 60” Deep.
Main Pod
[Section A]
Back Wall
[Section C]
Topper
[Section D]
Middle Wall
[Section B]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Insert power
supply into
bottom of
camera
Mount camera onto
tripod head using the screw
slot on the the bottom
On the back wall of the booth,
take a tape measure and mark
the wall with a piece of tape at 75”
Zoom out as far as possible
and line the 75" mark at the
very top of the view finder
and lock the camera.
Have a subject stand against the
back wall inside the Superbooth
and zoom in all the way.
Focus the camera on
the subject and zoom out
all of the way.
Plug the USB cable
into the left side of the camera
Set the lens
focus mode
switch to
<
MF
>
Set the power
switch to
<
ON
>
Set the mode
dial to
<
M
>
Display the menu
screen by pressing
the menu button
On the menu screen
select Quality
Under the
toolbar select
“Auto power off”
Attach the lens
Align the lens’
white or red
index mark
with the mark
on the camera
Change this setting
to
<
OFF
>
(Default is L)
Change this setting
to
<
S1
>
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Insert power
supply into
bottom of
camera
Mount camera onto
tripod head using the screw
slot on the the bottom
On the back wall of the booth,
take a tape measure and mark
the wall with a piece of tape at 75”
Zoom out as far as possible
and line the 75" mark at the
very top of the view finder
and lock the camera.
Have a subject stand against the
back wall inside the Superbooth
and zoom in all the way.
Focus the camera on
the subject and zoom out
all of the way.
Plug the USB cable
into the left side of the camera
Set the lens
focus mode
switch to
<
MF
>
Set the power
switch to
<
ON
>
Set the mode
dial to
<
M
>
Display the menu
screen by pressing
the menu button
On the menu screen
select Quality
Under the
toolbar select
“Auto power off”
Attach the lens
Align the lens’
white or red
index mark
with the mark
on the camera
Change this setting
to
<
OFF
>
(Default is L)
Change this setting
to
<
S1
>
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Insert power
supply into
bottom of
camera
Mount camera onto
tripod head using the screw
slot on the the bottom
On the back wall of the booth,
take a tape measure and mark
the wall with a piece of tape at 75”
Zoom out as far as possible
and line the 75" mark at the
very top of the view finder
and lock the camera.
Have a subject stand against the
back wall inside the Superbooth
and zoom in all the way.
Focus the camera on
the subject and zoom out
all of the way.
Plug the USB cable
into the left side of the camera
Set the lens
focus mode
switch to
<
MF
>
Set the power
switch to
<
ON
>
Set the mode
dial to
<
M
>
Display the menu
screen by pressing
the menu button
On the menu screen
select Quality
Under the
toolbar select
“Auto power off”
Attach the lens
Align the lens’
white or red
index mark
with the mark
on the camera
Change this setting
to
<
OFF
>
(Default is L)
Change this setting
to
<
S1
>

Sega SuperBooth Specifications

General

Brand	Sega
Model	SuperBooth
Category	Digital Signage
Language	English