Segway P100 S - Certifications and Compliance; Brand and Legal Information

Note that the expected service life of components is estimated based on ordinary use and proper maintenance of KickScooter.
Extensive and/or aggressive use of this KickScooter, failure to follow the instructions in this user manual, a user’s riding habits,
road condition, environment (e.g., temperature, humid or sunlight) will reduce reasonably expected service life of parts and/or
components of this KickScooter. Thus, it is recommended on conducting inspection and replacement more often than
suggested above. In-warranty service only covers defects in materials and workmanship for the KickScooter and its
components. In-warranty service does not cover damage to the KickScooter and its components caused by normal wear and
tear, abuse, neglect, misuse (including faulty repair, replacement or maintenance by anyone other than Segway authorized
service provider listed on https://store.segway.com/warranty-information), unauthorized modification, extreme environment
(including extreme temperature or humidity), extreme physical or electrical stress or interference, fluctuation or surges of
electrical power, lightning, static electricity, fire, acts of God or other external causes.
To ensure safe riding, day to day care and regular maintenance are essential. You, the owner, havecontrolandknowledgeof
howoftenyouuseyourscooter,howhardyouuseitandwhereyouuseit. It is the owner's responsibility to perform regular checks
and bring your scooter to authorized service center for inspection and service. Please refer to the maintenance schedule
below.
Note: This maintenance schedule charges a service fee.
Recommended Maintenance Schedule
4
Item Component
Mainframe parts Use a soft, wet cloth to wipe the mainframe clean.
Tire pressure
Inflate tires to 30–45 psi. Note: Remember to screw
the valve cap after inflating!
Tire wear
Screws on the
stem top
Mainframe
maintenance
Mainframe
maintenance
Screws on the
folding
mechanism
Check if the tires are cracked, deformed, or
significantly worn.
Tighten the six screws fixed with the handlebar and the
stem. The suggested torque is 3 N·m.
Tighten the screw on the throttle. The suggested
torque is 2.5 N·m.
Tighten the screws on the brake levers. The suggested
torque is 13 N·m.
Tighten the screws on the stem top. The suggested
torque is 2.5 N·m.
Tighten the two screws fixed with the front fork and the folding
mechanism. The suggested torque is 15 ± 1 N·m.
If the stem gets shaky when riding, tighen the screw on the
folding mechanism when the scooter is in folded state. The
suggested torque is 10 ± 1 N·m.
Brake disc
assembly
Tighten the screws on the brake disc assembly. The suggested
torque is 7.5 N·m.
Maintenance method
Every 3
months
Every 6
months or
every 310
miles (500
km)
After 2 years or
the total
mileage > 3107
miles (5000
km)
√√
√√
√√√
√√√
√√√
Item Component
Hub motor
Rear wheel
maintenance
Brake
adjustment
Brake pads
Front and rear
dual trailing arm
suspension
To accelerate and decelerate, check if the hub motor is stalled
or has abnormal sounds.
Check if the rear wheel is stalled or gets shaky, or the axis shaft
is unbalanced.
1) Test method:
Step 1: Squeeze the brake levers, let the brake lever make
contact with the handlebar grip (the distance ≤ 10 mm).
Step 2: Push the scooter, check if the front wheel moves slowly
forward.
2) If the brake is too tight/loose, use the 5 mm Allen key to
loosen the screw on the caliper. Then slightly adjust the brake
line (decrease/increase the exposed length), and tighten the
screw again.
Squeeze brake levers and check if the the brake pads are
significantly worn.
No severe abnormal sounds when riding.
Lift the front and rear wheel off the ground respectively, there
shall no visible swing from up/down or left/right.
Function
Inspection
maintenance Method
Every 3
months
Every 6
months or
every 310
miles (500
km)
After 2 years or
the total
mileage > 3107
miles (5000
km)
√√
√√
√√
√√
√√
√√
√
√√√
Brake rotor
Taillight Squeeze brake levers, the tail light works normally.
Spin the wheels, the caliper should be aligned with the rotor and
they shouldn't rub on the brake pads.
Headlight Check the headlight and see if it lights brightly.
Dashboard Power on the scooter, the dashboard works properly.
Horn Press the horn button, the sound is loud.
Throttle
Press and hold the throttle then release it, checking for
acceleration and deceleration.
Note: Release it, check if the throttle will back to the position.
√√
√√
√√
√√
√√
√√
EN EN
01 02 03 04 05 06 07 08 09 10 11 12 13 14