Seima LIARA - User Manual

To Next Page

Large end of pan connector can

be trimmed to suit setout.

Threaded

section can

be trimmed to

required size.

IMPORTANT

1 Inspect the components before installation to ensure there are no visible defects.

If a defect is found, do not install the toilet suite and contact the supplier

immediately. Claims for defects will not be accepted after the product has been

installed.

2 This toilet suite is suitable for a variety of set-ups:

Cistern — accommodates either Back Entry Inlet connection or Bottom Entry Inlet

connection (left or right stop valve).

Pan — universal trap — accommodates S-trap installation or P-trap installation

(using appropriate connector; not supplied).

3 The toilet suite must be installed by a licensed plumber. Failure to do so may void

the warranty.

4 Installation must be in accordance with AS/NZS3500.

CISTERN PACKAGE CONTENTS

1 x ceramic cistern lid

1 x ceramic cistern base

Cistern is supplied with flush

valve and dual purpose inlet

valve already installed.

PAN PACKAGE CONTENTS

1 x ceramic pan 1 x pan connector

For connecting pan to floor

outlet pipe/S-trap.

1 x threaded section (with

flange plate)

Flange attaches to wall;

threaded section links to

pan connector.

2 x concealed fixing

brackets

Optional — can be

used to connect pan

to floor.

2 x floor bolts

(+ white plugs)

2 x washers

Optional fixing #2 — used

with fixing brackets to

secure pan to floor. Bolt is

inserted through bracket

base hole.

2 x caps (chrome plated)

2 x screws

2 x pan plugs (white)

Optional fixing #2 — used to

secure pan to concealed fixing

bracket. Plastic plug is placed

into hole in side of pan exterior,

screw is rebated into plug and

then screws into a hole in upright

section of bracket. Chrome cap

is used to cover plastic plug.

2 x bolts w seals

For attaching cistern to

pan. White component

at top enables hand

tightening.

2 x plugs

Plugs can be used to plug

holes in sides of pan if

required.

1 x rubber seal

For sealing outlet at

base of cistern.

1 x flush button

Half flush left, full flush

right.

Note: The cistern can

be adapted for bottom

entry plumbing. The

bottom entry inlet

valve shown above is

included.

bottom entry

inlet valve

liara-wf-in | v 200 | page 1 of 4

INSTALLATION GUIDE

LIARA WALL FACED

seima.com.au

Please note

− Installation shall be in accordance with AS/NZS3500.

− All measurements are in millimetres. Height dimensions are to base of pan. Make allowance for bedding.

− Bedding: Fix pan to ﬂoor using a sand cement mixture of 3:1 to a depth of 60mm. Do not use lime or fast-drying cement.

− Bracket ﬁxing: The pan should be bedded with an acetic cured silicone sealant and ﬁxed with the brackets supplied.

− Dimensions are nominal and subject to normal ceramic manufacturing variations.

− Speciﬁcations may vary without notice as part of our continuous improvement practices.

− Clean with a damp cloth. Do not use abrasive cleaners, liquids or pastes.

Need help?

Do you have a question about the Seima LIARA and is the answer not in the manual?

The Seima Liara Wall Faced toilet suite is a modern and versatile toilet system designed for a variety of plumbing setups. This installation guide provides comprehensive instructions for both S-trap and P-trap installations, as well as options for back entry and bottom entry inlet plumbing.

Function Description:

The Liara Wall Faced toilet suite consists of a ceramic pan, a ceramic cistern base, and a ceramic cistern lid. It features a dual-flush system for water conservation, with a half flush (left button) and a full flush (right button). The cistern comes pre-assembled with a flush valve and a dual-purpose inlet valve, ready for back entry plumbing, but can be adapted for bottom entry. The pan is designed with a universal trap, accommodating both S-trap (floor outlet) and P-trap (wall outlet) installations using appropriate connectors (not supplied). The toilet seat is designed for easy installation and removal, featuring receptor holes that slide onto stainless steel pins, and buttons for quick release for cleaning.

Important Technical Specifications:

Setout Range: The recommended setout for S-trap installation is 150mm, with a range of 90-190mm.
Pan Connector Height: The height measurement from the floor to the center of the pan connector is 185mm.
Cistern Inlet: The cistern is supplied with a dual-purpose inlet valve that can be configured for either back entry (1/2" BSP nipple) or bottom entry (left or right stop valve) plumbing.
Fixing Methods: The pan can be secured to the floor using either cement bedding (sand cement mixture of 3:1 to a depth of 60mm) or concealed fixing brackets with floor bolts and screws. The cistern fixes directly onto the pan and does not require wall fixing.
Dimensions: All measurements are in millimeters.
- Overall Height (Pan + Cistern): Approximately 860mm.
- Pan Height: Approximately 420mm.
- Pan Depth (from wall): Approximately 650mm.
- Pan Width: Approximately 370mm.
- Cistern Height: Approximately 770mm.
- Cistern Width: Approximately 385mm.
- Cistern Depth: Approximately 145mm.
- Seat Connection Holes: Spacing of 145mm.
- Bottom Entry Inlet Port Hole: Located on both sides of the pan.
- Bracket Fixing Holes: Located on both sides of the pan.
Materials: Ceramic pan, cistern base, and lid. Stainless steel components for seat fixing (caps, plates with pins, toggle bolts). Rubber seals for cistern outlet and inlet valve. Plastic pan connector and threaded section. Chrome-plated caps for concealed fixings.
Compliance: Installation must be in accordance with AS/NZS3500.

Usage Features:

Dual Flush: Press the left button for a half flush to save water, and the right button for a full flush.
Versatile Plumbing: Can be configured for back entry or bottom entry water supply, offering flexibility for different bathroom layouts.
Universal Trap: Compatible with both S-trap (floor outlet) and P-trap (wall outlet) waste connections.
Hand-Tightened Bolts: The bolts for attaching the cistern to the pan feature a white component at the top for easy hand tightening.
Concealed Fixings: Optional concealed fixing brackets provide a clean aesthetic by hiding the floor bolts and screws under chrome caps.
Easy Seat Removal: The toilet seat can be easily removed for cleaning by putting it in an upright position, pressing the buttons on the seat, and lifting upwards. To fit, simply slide the seat down onto the stainless steel pins.

Maintenance Features:

Cleaning: Clean the toilet with liquid detergent and a damp cloth.
Avoid Abrasives: Do not use abrasive cleaners, liquids, or pastes, as these may damage the ceramic surface.
No Cistern Additives: Do not place water additives inside the cistern, as chemicals may damage the valves and impair the functionality of the cistern.
Seat Removal for Cleaning: The quick-release seat mechanism allows for thorough cleaning of both the seat and the toilet bowl.
Regular Checks: Periodically check the operation of the cistern and flush button to ensure proper functionality. Ensure water supply connections are secure and free from leaks.

Seima LIARA Specifications

General

Brand	Seima
Model	LIARA
Category	Toilets
Language	English