SELWOOD Seltorque S100 User Manual

Selwood Seltorque S100 Manual
1
SELWOOD SELTORQUE S100
ELECTRIC SUPERSILENT
7.5KW STATIC – 1097206000
7.5KW S/SILENT – 1016133S40
The products of Selwood Limited, are designed,
developed and produced in the company's Chandler's
Ford factory. Many features are covered by world-
wide patents. Product names such as Spate, Simplite
and Seltorque, are registered trade marks.
As all products are subject to continuous development,
the company reserves the right to alter the
specifications and information given in this manual
without prior notice.
Whilst every care has been taken in the preparation of
this publication the information it contains must not be
regarded as binding.
Amendments to this publication will only be issued to
cover those design changes which fundamentally alter
the build or operation and servicing procedures. They
will be distributed through the company's dealers and
agencies.
Your attention is drawn to the following symbols used
throughout this manual:-
CAUTION
This caution symbol draws attention to special
instructions or procedures that, if not correctly
followed, may result in damage to, or destruction of
equipment.
WARNING
This warning symbol draws attention to special
instructions or procedures that, if not strictly
observed, may result in personal injury.
WARNING
A WARNING SYMBOL WITH THIS TYPE OF
TEXT DRAWS ATTENTION TO SPECIAL
INSTRUCTIONS OR PROCEDURES WHICH, IF NOT
STRICTLY OBSERVED MAY RESULT IN SEVERE
PERSONAL INJURY, OR LOSS OF LIFE.
Additional copies of this manual are available
from Selwood Pt No 1016133S40MAN
Published by Selwood Limited
© Selwood Limited June 2016
Instructions for Ordering
Replacement Parts
1. Always quote the pump serial number located on
the plate fastened to the bearing and air pump
mechanism housing.
2. Always quote the part number(s) (ten digit) of the
component(s), NOT the item number(s).
3. Always quote the description of the component(s).
Items usually supplied together as sub-assemblies will
have the sub-assembly part number printed at the
bottom of the relevant page.
HEALTH AND SAFETY AT WORK
As manufacturers of pumps and associated equipment
we wish to inform you that, in compliance with Section
6 of the Act, safety precautions should be taken with
our products.
We take every care to ensure as is reasonably
practicable that our products are safe and without risk
to health when properly used. Nevertheless,
appropriate health and safety precautions must be
taken, and in particular you are requested to have
special regard to the operational and safety
requirements leaflet P769 which accompanies each
pump on despatch from our premises.
Q
U
A
L
I
T
Y
A
S
S
U
R
E
D
F
I
R
M
Our products also conform to the E.E.C. Machinery
Safety Directive and carry the C.E. mark.
WARNING
Pumps and engines may be fitted with
seals or 'O' rings manufactured from
VITON or similar material.
When temperatures reach 400°C
(720°F) a corrosive acid is produced,
which cannot be removed from the skin.
If signs of material decomposition are
evident, or if in doubt, always wear
disposable heavy-duty gloves.

SELWOOD Seltorque S100 Specifications

General

Brand	SELWOOD
Model	Seltorque S100
Category	Water Pump
Language	English

Summary

Instructions for Ordering Replacement Parts

Part Ordering Process

Steps for ordering replacement parts, including required information.

Health and Safety at Work

General Safety Information

Overview of safety precautions and responsibilities for product use.

Viton Material Hazard

Specific warning about hazards associated with Viton seals at high temperatures.

Safety Precautions

Critical Safety Warnings

Essential safety instructions to prevent severe personal injury or loss of life.

Operational Safety Guidelines

Guidelines for safe operation, including hose and pressure limits, and noise exposure.

General Information and Maintenance

Installation and Operation

Guidance on pump installation, operation, and electrical motor safety.

Lubrication and Fastening

Details on pump lubrication, fastening torques, and warranty conditions.

Routine Maintenance

Major Servicing: Air Pump and Separator

Air Pump Maintenance Procedures

Detailed steps for servicing the air pump, including valves, seals, and actuators.

Separator Maintenance Procedures

Instructions for servicing the separator, float, and peel valve.

Major Servicing: Impeller, Seals, and Valves

Impeller, Mechanical Seal, and Delivery Valve Servicing

Procedures for servicing the impeller, mechanical seal, and delivery valve.

Major Servicing: Associated Components

Flushing Chamber and Air Pump Mechanism Maintenance

Procedures for maintaining the flushing chamber and air pump mechanism.

Bearings and Lip Seal Maintenance

Guidance on replacing bearings and lip seals in the drive shaft assembly.

Workshop Tools and Procedures

Servicing Tools and Procedures Overview

List of recommended workshop tools and their care for major servicing.

Seal Assembly Procedures

Actuator Neck, Mechanical Seal, and Drive Rod Seal Procedures

Detailed instructions for removing and fitting various seals and components.

Seal Housing and Bearing Bush Procedures

Seal Housing and Bearing Bush Installation

Steps for fitting the seal housing and replacing the drive rod bearing bush.

Flushing Chamber and Impeller Procedures

Flushing Chamber, Eccentric, and Impeller Procedures

Procedures for assembling the flushing chamber and removing the eccentric and impeller.

Bearing Installation Procedures

Drive End and Impeller End Bearing Installation

Instructions for fitting replacement drive end and impeller end bearings.

Drive Shaft Assembly Procedures

Drive Shaft and Bearings Assembly into Housing

Steps for assembling the drive shaft with bearings into the housing.

Fault Finding Guide

Pump Prime and Performance Issues

Troubleshooting guides for prime loss and reduced output or head.

Specific Fault Scenarios

Water Carry-Over, Leaks, and Rotation Issues

Diagnosing and resolving specific faults like water carry-over, leaks, and rotation problems.

Troubleshooting Unexpected Noises

Pump Noise Diagnosis and Resolution

Identifying and addressing the causes of unexpected noises during pump operation.

Parts List - Air Pump Components

Air Pump Parts List

List of part numbers and descriptions for air pump components.

Parts List - Separator Components

Separator Parts List

List of part numbers and descriptions for separator components.

Parts List - Delivery Valve Components

Delivery Valve Parts List

List of part numbers and descriptions for delivery valve components.

Parts List - Pump Body Components

Pump Body Parts List

List of part numbers and descriptions for pump body components.

Parts List - Bearing Housing and Drive Assembly Components

Bearing Housing and Drive Assembly Parts List

List of parts for the bearing housing and air pump drive assembly.

Parts List - Static Chassis Configuration

Static Chassis Components List

List of parts for the S100/7.5kW 400/3/50 on static chassis.

Parts List - SuperSilent Canopy Configuration

SuperSilent Canopy Components List

List of parts for the S100/7.5kW SuperSilent canopy build.

Wiring Diagrams

3 Phase DOL Motor Wiring

Diagrams for motor terminal connections and winding configurations.

PTC Thermistor Windings

PTC Thermistor Terminal Connections

Diagram showing PTC thermistor winding connections.

Space Heater Information

Space Heater Details and Ratings

Information on space heater connections, power output, and resistance.

Standard Terminal Box Dimensions

Terminal Box Specifications and Accessories

Details on terminal box dimensions, accessory boxes, and connector counts.

Axial Fan Specifications

Axial Fan Product Drawing and Connection

Product drawing, dimensions, and connection screen for the axial fan.