Sena TUFFTALK-LITE-01 User Manual

Sena Tufftalk Lite Headset - Features & Instructions
Page 1 of 5
Power On / Off
• Power On: Hold down the Center Button and the Plus (+) Button at the same time until the blue LED
appears. You’ll hear a voice prompt say “Hello”. The red LED will flash a certain number of times to
indicate the battery level.
4 flashes = High, 70% ~ 100%
3 flashes = Medium, 30% ~ 70%
2 flashes = Low, 0% ~ 30%
When you power on the headset, keep holding down the Center Button and the Plus (+) Button for
about 3 seconds until you hear high tone triple beeps. You will hear a voice prompt indicating that the
battery level is High, Medium, or Low.
• Power Off: Hold down the Center Button and the Plus (+) Button at the same time until the red LED
appears. You’ll hear a voice prompt say “Goodbye”.
Pairing to Devices (Phone, standalone GPS, etc.)
The Tufftalk Lite needs to be placed into one of the various pairing modes for it to be paired to a device
like a smartphone.
• Enter the Configuration by holding down the Center Button for 10 seconds until you hear the
voice prompt say “Configuration menu”.
• Tap the Plus (+) Button once to cycle to the first pairing mode. You will hear the voice prompt
say “Phone pairing”.
• Tap the Center Button once to select Mobile Phone Pairing mode. You will hear the voice
prompt say “Phone pairing” and the LEDs will start flashing red and blue rapidly.
With a smartphone paired to the Tufftalk Lite, you can use the headset to make and receive phone calls,
listen and control music playback and configure settings through Sena Smartphone App.
Make and Receive Phone Calls
Make Phone Calls
The voice dialer on a paired smartphone, such as Siri on the iPhone, needs to be used to make a phone
call.

Sena TUFFTALK-LITE-01 Specifications

General

Talk time	Up to 15 hours
Headset Profile	Yes
Hands-Free Profile	Yes
Battery Type	Lithium Polymer
Working Distance	Up to 800 meters (0.5 miles) in open terrain
Charging time	3 hours
Operating Temperature	-10°C to 55°C (14°F to 131°F)
Microphone	Built-in
Compatibility	Bluetooth-enabled devices

Summary

Power On / Off

Power On and Battery Status

Turn on the headset, check LED indicators for battery level, and listen to voice prompts.

Power Off

Turn off the headset by holding buttons until red LED appears and voice prompt is heard.

Pairing to Devices

Phone Pairing Procedure

Steps to enter configuration, select phone pairing mode, and confirm with LED indications.

Make and Receive Phone Calls

Make Phone Calls

Initiate calls using the voice dialer on a paired smartphone like Siri.

Receive Phone Calls

Answer, end, or reject incoming calls using the Center Button or voice commands.

Two-Way Intercom

Two-Way Intercom Pairing

Pair two Tufftalk Lite headsets for full-duplex intercom communication.

Connect or Disconnect Intercom

Connect or disconnect an established intercom session by tapping the Center Button.

Group Intercom Features

Three-Way Intercom

Communicate with 3 different people simultaneously using intercom pairing.

Four-Way Intercom

Communicate with 4 different people simultaneously using intercom pairing.

Group Intercom Setup

Connect multiple helmets for group intercom communication.

Control Music Playback

Music Control Operations

Play, pause, adjust volume, and track forward/backward music from a paired smartphone.

Music Sharing

Share music being listened to over Bluetooth with one intercom friend.

FM Radio

FM Radio Operation

Turn FM radio on/off and retain the last station frequency upon power cycle.

FM Radio Scanning and Presets

Scan for stations, save current station as preset, and create temporary presets.

Remote Control

Remote Control Pairing

Pair the headset with a Sena remote to control Bluetooth functions remotely.

Changing Settings

Settings Management

Adjust headset settings via Configuration Menu, Sena Device Manager, or Sena Smartphone App.