EasyManua.ls Logo

Sencor STR 210 - Page 4

Sencor STR 210
28 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
EN-3 CZ-1
EN
Warranty conditions
Warranty card is not apart of the device packaging.
This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty is limited
to the following conditions. Warranty is referred only to the customer goods using for common domestic use. The
claim for service can be applied either at dealer’sshop where the product was bought, or at below mentioned
authorized service shops. The end-user is obligated to set up aclaim immediately when the defects appeared but
only till the end of warranty period. The end user is obligated to cooperate to certify the claiming defects. Only
completed and clean (according to hygienic standards) product will be accepted. In case of eligible warranty claim
the warranty period will be prolonged by the period from the date of claim application till the date of taking over
the product by end-user, or the date the end-user is obligated to take it over. To obtain the service under this
warranty, end-user is obligated to certify his claim with duly completed following documents: receipt, certificate of
warranty, certificate of installation.
This warranty is void especially if apply as follows:
Defects which were put on sale.
Wear-out or damage caused by common use.
The product was damaged by unprofessional or wrong installation, used in contrary to the applicable instruction
manual, used in contrary to legal enactment and common process of use or used for another purpose which
has been designed for.
The product was damaged by uncared-for or insufficient maintenance.
The product was damaged by dirt, accident of force majeure (natural disaster, fire, and flood).
Defects on functionality caused by low duality of signal, electromagnetic field interference etc.
The product was mechanically damaged (e.g. broken button, fall).
Damage caused by use of unsuitable media, fillings, expendable supplies (batteries) or by unsuitable working
conditions (e.g. high temperatures, high humidity, quakes).
Repair, modification or other failure action to the product by unauthorized person.
End-user did not prove enough his right to claim (time and place of purchase).
Data on presented documents differs from data on products.
Cases when the claiming product cannot be indentified according to the presented documents (e.g. the serial
number or the warranty seal has been damaged).
Authorized service centers
Visit www.sencor. for detailed information about authorized service centers. com
Účel použití
Tato rotační řezačka je navržena pro kreativní řezání papíru, fólie a dalších měkkých materiálů.
Umožňuje řezat až 5 listů (80 g/m
2
) současně.
Bezpečnostní pokyny
IV případě jakéhokoli poškození, které vzniklo v důsledku nedodržení pokynů v tomto
návodu k obsluze, nesprávné obsluhy nebo nedodržení bezpečnostních pokynů
pozbývá záruka platnosti.
Nepřenášejte tento produkt za řezací hlavu.
Nepřetěžujte tuto řezačku papíru. Nevkládejte více listů nebo silnější listy, než je uvedeno
v technické specikaci.
Nedotýkejte se čepelí nožů. Hrozí nebezpečí zranění!
Uschovejte prosím tento návod k obsluze pro pozdější použití!
Pokud toto zařízení předáváte jiné osobě, předejte s ním prosím i tento návod k obsluze.
Popis produktu
Tato řezačka papíru má následující vlastnosti:
průhledné pravítko se stupnicí
3 různé nože pro přímý řez, vlnový řez a děrování papíru
řezání je možné v obou směrech
přídavná stupnice na základní desce pro přímé a snadné vyrovnání řezaného materiálu
Výměna nožů
Nedotýkejte se ostří čepelí nožů. Hrozí nebezpečí zranění!
Otočte kryt u řezací hlavy směrem k poloze OPEN(Otevřeno) a vyjměte jej.
Vyjměte nůž.
Vytáhněte požadovaný nůž z jeho držáku v dolní části základní desky a opatrně odstraňte
ochranu čepele.
Vložte do řezací hlavy nový nůž. Osa nože musí být správně vložena do objímky v řezací hlavě.
Umístěte kryt zpět na řezací hlavu a otočte jej směrem k poloze LOCK(Zajištěno) tak, aby
zacvakl do správné polohy.
Vložte vyměněný nůž do ochrany čepele a umístěte jej do držáku v dolní části základní desky.