This document is an operator's manual for a Senix 4-Cycle 1.9 cu in. (31 cc) Engine Gasoline Powered Blower Vacuum, model BLV4QL-M. It provides comprehensive information on safety, assembly, operation, maintenance, and repair.

Function Description:

The Senix BLV4QL-M is a versatile outdoor power tool designed for both blowing and vacuuming/mulching tasks. It is powered by a 4-cycle gasoline engine, making it suitable for clearing leaves, grass clippings, and other light debris from various surfaces such as lawns, patios, driveways, and gardens. In blower mode, it generates a high-speed air stream to move debris. In vacuum mode, it collects debris into a bag and mulches it, reducing its volume for easier disposal. The unit is intended for occasional, household use.

Important Technical Specifications:

Model Number: BLV4QL-M
Engine Type: Air-Cooled, 4-Cycle
Displacement: 1.9 cu in. (31 cc)
Spark Plug Gap: 0.025 - 0.030 in. (0.6 - 0.8 mm)
Lubrication: SAE 30 Oil
Crankcase Lubrication Capacity: 2.03 oz. (60 ml)
Fuel Tank Capacity: 9.47 oz. (280 ml)
Blowing Air Speed: 127 mph (205 km/h)
Volume of Air Moved (Blower): 425 CFM (720 m³/h)
Vacuum Air Flow Max: 550 CFM (930 m³/h)
Mulch Reduction Ratio: 10:01
Bag Capacity: 1.37 bushel
Blower Weight (no fuel): 9.26 lbs (4.2 kg)
Vacuum/Mulcher Weight (no fuel): 12.80 lbs (5.8 kg)

Usage Features:

The BLV4QL-M is designed for user-friendly operation with clear controls and safety guidelines.

Starting: The unit features a primer bulb (push 10 times) and a choke lever (Full Choke position for starting). The ON/OFF switch is always in the ON (1) position for operation. A starter rope grip is used to manually start the engine.
Stopping: To stop the engine, release the throttle control to idle, then press and hold the ON/OFF switch in the OFF (STOP) position until the engine completely stops.
Blower Mode: The blower tube is attached to the blower outlet. The unit should be held with both hands, keeping feet apart and firmly planted, and held in front of and away from the body. The air stream should be directed away from people, animals, windows, or automobiles.
Vacuum Mode: This mode involves attaching a curved tube through the zipper of the bag, connecting the curved tube to the blower outlet, and then assembling lower and upper vacuum tubes which are inserted into the machine. The unit collects debris into the bag and mulches it.
Safety Precautions: Emphasizes wearing eye and hearing protection, heavy-duty work gloves, and slip-resistant boots. It warns against operating when tired or under the influence, allowing children to operate, or operating without proper guards. Users are advised to clear the operating area of bystanders (at least 50 feet/15 m) and foreign objects. The manual stresses operating in well-ventilated outdoor areas due to carbon monoxide fumes and avoiding hot surfaces like the muffler or cylinder.
Fueling: Requires unleaded fuel and SAE 30 oil. Fueling should be done outdoors, away from sparks or flames, with a cool engine. The fuel cap should be loosened slowly to release pressure and tightened securely after refueling. Spilled fuel must be wiped up, and the unit moved 30 feet from the fueling site before starting. E85 fuel is explicitly warned against as it can damage the engine and void the warranty.

Maintenance Features:

Regular maintenance is crucial for the longevity and safe operation of the BLV4QL-M.

General Cleaning: Avoid using solvents on plastic parts. Use clean cloths to remove dirt, dust, lubricant, and grease. Keep the unit clean, removing vegetation and debris from moving parts.
Fuel System: Regularly check for fuel leaks in the fuel cap, tank, and lines. Replace any leaking components immediately. The fuel cap contains a non-serviceable filter and check valve; if performance issues arise and improve when the cap is loosened, the cap may need replacement.
Spark Plug Replacement: The engine uses a Champion RY4C or equivalent spark plug with a 0.025 in. electrode gap. It should be replaced annually. Caution is advised to avoid cross-threading.
Engine Lubricant Change: Oil must be added before initial use as the unit is shipped without oil in the crankcase. The unit comes with a 2.03 fluid oz. (60 ml) container of SAE 30 oil for initial fill. Oil changes should be performed when the engine is warm but not hot to allow for quicker and more complete draining. The process involves stopping the engine, allowing it to cool, removing the engine cover, disconnecting the spark plug wire, removing the oil fill cap/dipstick, tipping the blower to drain old lubricant, and refilling with new SAE 30 oil. Used lubricant must be disposed of at an approved site.
Storage: After use, the product should be cleaned of all foreign material and stored indoors in a dry, well-ventilated area inaccessible to children, away from corrosive agents. All ISO and local regulations for safe gasoline storage and handling must be followed.
Troubleshooting Guide: The manual includes a troubleshooting section to help diagnose common issues such as the engine not starting, idling incorrectly, not accelerating, or lacking power/stalling. It provides possible causes (e.g., empty fuel tank, old fuel, fouled spark plug, dirty air filter, incorrect idle speed) and recommended actions (e.g., refill with fresh fuel, press primer bulb, drain and refill fuel, replace spark plug, clean/replace air filter, adjust idle speed).

Senix BLV4QL-M - Page 31

Table of Contents

Related product manuals