SERRMAC RAG TCO 28 - User Manual

93 pages

Save Page as PDF

To Next Page

OPERATING INSTRUCTIONS BOOK

COLUMN DRILLING MACHINES

R A G T C O 2 8 --- 3 2 --- 3 5 --- 4 0 L --- 4 0 P

Serial Nº

MODELL

Main Page

Table of Contents3
Foreword6
Conventions and Abbreviations Used in the Text7
General8
Manufacturer's Data8
Identification of the Machine Model8
Adress Abroad8
Retaileràs Data8
Manufacturer's Data9
CE" Declaration of Conformity9
General Test and Inspection Certificate10
Notes on Standards10
Warranty11
Safety13
General Safety Regulations13
Modifications Are Prohibited13
Periodical Safety Checks14
Machine Noise Emission14
Drawing with Special Indications15
Danger Areas and Safety Devices Applied15
Lifting and Transportation16
Mass16
When the Machine Is Still Packed16
After Unpacking the Machine17
Machine Installation18
Fixing the Machine to the Floor18
Assembling the Spindle Guard18
Lighting the Working Place19
Connecting - Disconnecting the Machine from the Mains20
Power Supply Characteristics20
Environmental Conditions, Pollutants, Rating Plate20
Power Supply Cable21
Connecting Procedure22
Protection of Electric Equipment22
Procedure for Connection to the Mains22
Requirements Regarding the Grounding System23
Protection against Atmospheric Discharges24
Procedure for Disconnecting the Machine from the Mains24
Preliminary Checks25
Technical Data of the Machine26
Overall Dimensions26
Operation Capacity29
Motors Ratings. Power and Spindle Rotations29
Work Table Data29
Vice30
Safety Prescriptions (During Machining)31
General Instructions31
Safety Prescriptions (before Starting to Machine)31
Emergency32
Resetting after an Emergency Stop32
Blocking the Tool and Removing It from the Spindle33
When Drilling33
When Milling (Only for Tco 3534
Description of All the Control and Drive Elements, Their Location and Use35
Controls Located on the Front Panel Switchboard35
Step Pulleys (PU)36
Changing Gears (CI)38
Single Variator (VS)39
Delay Variator (VR)40
Spindle Downstroke with Cutting Depth Stop. Z Axis41
Manual Spindle Downstroke41
Machine Not Equipped with Automatic Downstroke Da)41
Spindle Downstroke (Machine Equipped with Automatic Downstroke Da)42
Spindle42
Stop the Machine42
Automatic Spindle Downstroke with Lead Screw (Optional)45
Description of Table Unit Controls and Use46
Adjustments and Locking Devices46
Rectangular Table46
Cross Table (Tco 3547
Machine Maintenance48
General Instructions48
Lubrication48
Lubrication Points48
Leadscrew Lubrication. (Optional)49
Spare Parts and Components50
Components' Disassembling and Assembling Operations50
Replacement of Cross Lever Spring for Spindle's Downstroke50
Replacement of Cross Lever Spring for Spindle's Downstroke51
Replacement of Gear53
Replacement of Control Panel Fuses54
Disassembly of Variator Lever and Springs of Motor Pulley (for Model Vs54
Replacement of Belts55
Leadscrew Disassembly and Reassembly57
Replacement of Spindle Shaft's Bearings58
Replacement of Pulley Carrier Bearings58
Faceplate Adjustment60
Backlash Adjustment of Shaft's Guides (3560
Replacement of Screws61
Of Cross Table's Axes (3561
Lamp Replacement63
Spare Parts and Components64
Assembling the Spindle Guard65
Spindle Manual Downstroke (Tco 28)73
Spindle Manual Downstroke. (Tco 3274
Remote Spindle76
Base Column77
Base Column79
Cross Table (3580
Column81
Cross Table (Tco40P Tc)82
Diagrams83
Functions List92
Parts List92

Need help?

Do you have a question about the SERRMAC RAG TCO 28 and is the answer not in the manual?

SERRMAC RAG TCO 28 Specifications

General

Brand	SERRMAC
Model	RAG TCO 28
Category	Drill
Language	English

SERRMAC RAG TCO 28 - User Manual

Table of Contents

SERRMAC RAG TCO 28 Specifications