EasyManua.ls Logo

Seuic CRUISE2 - User Manual

Default Icon
76 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
SEUIC Technologies Co., Ltd.
SEUIC
Reference Manual
CRUISE2 Industrial-Grade Smartphone
Service Manual of Android System Products
Version: 1.1

Table of Contents

Questions and Answers

  • C
    cmeltonAug 15, 2025
    How to fix a Seuic Data Logger CRUISE2 that won't turn on?
    • R
      royericAug 15, 2025
      If your Seuic CRUISE2 Data Logger isn't powering on when you press the power button, there are several potential reasons. First, the battery might be too low or completely discharged; in this case, charge or replace the battery. Second, ensure you're pressing and holding the power button for 3 seconds, as a short press won't activate the device. Also, verify that the battery is correctly installed. Finally, if the system has experienced a breakdown, try performing a soft reset.
  • M
    Matthew StevensAug 18, 2025
    Why can't my Seuic Data Loggers access the internet through mobile data?
    • J
      Jason SanchezAug 18, 2025
      If you can't access the internet using mobile data on your Seuic Data Logger, first ensure that mobile data is enabled in the settings. If it is enabled, check that the correct network mode is selected and that your SIM card is properly registered. Finally, verify that your SIM card account is not in arrears and recharge if necessary.
  • K
    Kevin RhodesAug 21, 2025
    What to do if Seuic CRUISE2 Data Loggers won't decode bar codes?
    • E
      Elaine ThomasAug 22, 2025
      If your Seuic CRUISE2 Data Logger fails to decode a barcode, several factors could be responsible. First, ensure the scanning application is loaded on CRUISE2. Also, verify that the scanning program is set to the scan interface and not hidden within the Bar Code Settings or Application Settings. Check that the barcode is free from defects and is readable. Confirm that the barcode decoding function is enabled in the barcode settings interface. Finally, make sure the CRUISE2 is within the correct scan range.
  • D
    Dennis SmithAug 25, 2025
    Why does my Seuic CRUISE2 Data Loggers keep turning off?
    • M
      Melissa BeardAug 26, 2025
      Your Seuic CRUISE2 Data Logger might be powering off by itself due to two main reasons. If the device is in an inactive state, it will automatically turn off after a set period. You can adjust this time period in settings, setting it from 15 seconds to 30 minutes, or choose to never sleep. Alternatively, the battery may be running low, so try charging or replacing the battery.
  • D
    dawn90Aug 28, 2025
    Why aren't any Bluetooth devices found by my Seuic Data Loggers?
    • T
      Tonya WardAug 29, 2025
      If your Seuic Data Logger isn't finding nearby Bluetooth devices, there are a few things to check. Make sure the device is within 10 meters (32.8 feet) of the other Bluetooth devices. Verify that the Bluetooth devices you're trying to connect to are turned on. Also, ensure that those devices are set to discoverable mode.
  • R
    rloweAug 31, 2025
    Why can't I take pictures with my Seuic Data Loggers?
    • S
      Sierra FernandezSep 1, 2025
      If you're unable to take pictures with your Seuic Data Logger, and it prompts 'No Storage Device', exit USB Storage Mode. If you see a 'Camera Failure' message, it means the camera can't be turned on while the QR scan light is emitted after the QR code campaign is disabled. Alternatively, if the prompt says 'SD card space is insufficient', clear memory or switch the storage locations.
  • D
    donnahowellSep 4, 2025
    What to do if my Seuic Data Loggers rechargeable battery won't charge?
    • K
      kimvalerieSep 4, 2025
      If the rechargeable battery in your Seuic Data Logger isn't charging, it could be due to a battery failure, in which case you should replace the battery. Another possibility is that the battery temperature is too high or too low. If this is the case, keep the battery in a normal temperature environment.
  • H
    hcookSep 7, 2025
    What causes Seuic Data Loggers to fail connecting to AP?
    • W
      william72Sep 7, 2025
      If your Seuic Data Logger fails to connect to an Access Point (AP) and displays the message 'There is an authentication failure', the most likely cause is that the WLAN password you entered is incorrect.
  • M
    Miss Lauren JacksonSep 12, 2025
    How to fix no sound on Seuic Data Loggers?
    • S
      Samuel WhitneySep 12, 2025
      If there is no sound coming from your Seuic Data Logger, the volume might be too low or turned off. Try adjusting the volume.

Seuic CRUISE2 Specifications

General IconGeneral
ModelCRUISE2
BluetoothBluetooth 5.0
Expandable StorageUp to 128GB via microSD
Resolution480 x 800
Touch PanelMulti-point capacitive touch panel
Camera13MP rear camera
Wi-Fi802.11 a/b/g/n/ac, dual-band
NFCYes
GPSGPS, GLONASS, BeiDou
Barcode Scanner2D Barcode Scanner
ConnectivityWi-Fi, Bluetooth, USB, 4G LTE
PortsUSB Type-C
Durability1.5m drop resistance
Weight280g
Humidity Range5% to 95% (non-condensing)
Data Capacityexpandable to 128GB
Communication InterfaceUSB, Wi-Fi, Bluetooth, 4G
Software CompatibilityAndroid applications

Related product manuals