Sharndy ETW13C - User Manual

INSTALLATION GUIDE
! CAUTION — SURFACE OF UNIT IS HOT WHEN ON !! CAUTION — SURFACE OF UNIT IS HOT WHEN ON !
WARNINGS Please read the following information before installing and using
your Heated Towel Rack.
- These units should be installed by a certified electrician.
- The unit requires a 120 volt, 60Hz power source and should be installed on a protected circuit.
- Plug-in units should be connected to a grounded outlet with a minimum rating of 10 amps.
- Follow installation instructions to ensure unit is securely fixed to wall.
- Unit is designed for drying towels. Under no circumstances should anybody climb on or hang on unit.
- Unit is intended for indoor use only. Do not place units inside a shower, sauna, steam room, or wherever
unit would be exposed to water.
CAUTION
- As this is a heating device, the surface temperature can increase depending on the ambient temperature
and the towels applied to the unit.
- Overloading the unit will cause the unit to become extremely hot and may result in a burn if touched and/or
damage to towels.
- The fasteners provided with the installation kit are for convenience only and are not suitable for all
installation conditions.
- It is the ultimate responsibility of the installer to ensure suitable mounting hardware is used.
OPERATING INSTRUCTION
- After installation, connect the electric power and turn on switch.
- The indicator light will glow blue and the towel warmer will start to heat — Allow 10-20 minutes to heat up.
- This towel warmer has been designed to run continuously — Turn off the switch or unplug the cord when
the towel warmer is not in use for long periods of time.
- Never use an extension cord for Plug-in models.
- The towel warmer features an Integrated on/off switch.
- Remove plastic cover after installation.
- Press switch to power on unit.
- Switch will illuminate when on.
CARE & MAINTENANCE
- The unit is constructed from extremely durable stainless steel. To maintain a good appearance, follow
these simple instructions:
- For routine cleaning, simply switch off the unit, allow to cool to room temperature, wipe with a damp cloth.
- Under no circumstances should abrasive cleaners be used to clean the unit.
Email: support@SHARNDY.com
CONTACT US
Website: www.sharndy.com
Warranty: Three year limited warranty.With proof of purchase, will apply if all Terms and Conditions of
sale are met and Installation Instructions are adhered to.
ETW13C
68W
H26.77*W20.47*D4.33 inchesSize
Rated Voltage
120V, 60Hz
Rated Power
Control Mode Blue Metal on/off Switch
Length of the cable 4.8 ft / 1.6 m
Warramty 3 years
Model

Summary

Safety Warnings and Precautions

Installation and Usage Warnings

Essential safety guidelines for professional installation and proper unit usage, including electrical requirements and usage restrictions.

Temperature and Overload Cautions

Cautions regarding potential surface temperature increases and the risks associated with overloading the unit.

Mounting Hardware Responsibility

Information on the limitations of provided fasteners and the installer's ultimate responsibility for suitable mounting hardware.

Operating Instructions

Powering On and Heating Up

Steps for connecting power, turning on the unit, and the expected indicator light and heating process.

Continuous Operation and Safety

Guidance on the unit's continuous operation design and when to switch off or unplug.

Plug-in Model Specifics

Important notes for plug-in models, including the prohibition of extension cords and integrated switch operation.

Care and Maintenance

Routine Cleaning Procedure

Instructions for routine cleaning of the unit, emphasizing the use of a damp cloth and avoiding abrasive cleaners.

Contact and Warranty Information

Support Channels and Warranty Terms

Contact information for support and details regarding the three-year limited warranty terms and conditions.

Included Components and Tools

Component Identification

List and visual identification of all components included in the package for installation.

Required Tools for Assembly

List of necessary tools required for the successful assembly and installation of the towel warmer.

Installation Steps

Wall Bracket Preparation

Steps for preparing and attaching the wall brackets to the towel warmer unit.

Wall Marking and Drilling

Instructions for measuring, marking wall locations, and drilling holes for bracket installation.

Bracket Installation on Wall

Procedure for installing the wall brackets onto the wall using provided hardware and tools.

Final Assembly and Cleaning

Steps for fixing the brackets onto the wall mounts and final cleaning of the installed unit.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features
5. Installation Requirements and Warnings
6. Contact Information

This document describes the SHARNDY ETW13C Heated Towel Rack, an indoor-use appliance designed for drying towels.

Function Description:

The SHARNDY ETW13C is a heated towel rack that warms and dries towels. After installation and connection to an electric power source, the unit is activated by an integrated on/off switch, which illuminates blue when on. The towel warmer begins to heat up within 10-20 minutes. It is designed for continuous operation, but users should turn off the switch or unplug the cord when the unit is not in use for long periods. The primary function is to dry towels, and it is explicitly stated that no one should climb on or hang from the unit.

Important Technical Specifications:

• Model: ETW13C
• Dimensions: H26.77" x W20.47" x D4.33" (Height x Width x Depth)
• Rated Voltage: 120V, 60Hz
• Rated Power: 68W
• Control Mode: Blue Metal on/off Switch
• Length of the cable: 4.8 ft / 1.6 m
• Warranty: 3 years (with proof of purchase, adherence to terms and conditions of sale, and installation instructions)
• Power Source Requirement: Requires a 120 volt, 60Hz power source and should be installed on a protected circuit.
• Plug-in Units: Must be connected to a grounded outlet with a minimum rating of 10 amps.
• Construction Material: Extremely durable stainless steel.

Usage Features:

• Integrated On/Off Switch: The unit features an integrated on/off switch for easy operation. The switch illuminates blue when the unit is powered on.
• Quick Heating: The towel warmer starts to heat up within 10-20 minutes after being turned on.
• Continuous Operation: Designed to run continuously, offering consistent towel warming and drying.
• Indoor Use Only: The unit is strictly for indoor use and must not be placed inside a shower, sauna, steam room, or any location where it would be exposed to water.
• Safety Precautions:
  • The surface temperature can increase significantly, depending on ambient temperature and the number of towels applied.
  • Overloading the unit can cause it to become extremely hot, potentially leading to burns if touched or damage to towels.
  • Users are warned not to use an extension cord for plug-in models.
  • The unit should not be used for climbing or hanging anything other than towels.

Maintenance Features:

• Durable Construction: Made from extremely durable stainless steel, ensuring longevity.
• Routine Cleaning: For routine cleaning, the unit should be switched off and allowed to cool to room temperature. It can then be wiped with a damp cloth.
• Avoid Abrasive Cleaners: It is explicitly stated that abrasive cleaners must not be used to clean the unit, as they could damage the stainless steel finish.

Installation Requirements and Warnings:

• Professional Installation: Units should be installed by a certified electrician.
• Secure Mounting: Follow installation instructions to ensure the unit is securely fixed to the wall. The provided fasteners are for convenience only; the installer is ultimately responsible for ensuring suitable mounting hardware is used for specific installation conditions.
• Wall Bracket Installation: The installation process involves measuring and marking four wall bracket positions, drilling holes, inserting plastic expanders, and securing the brackets with screws. The unit should be installed at least 600mm above the floor level and checked for levelness and perpendicularity using a leveling instrument.
• Electrical Safety: Requires a grounded outlet with a minimum 10-amp rating for plug-in units and installation on a protected circuit.
• Hot Surface Warning: A prominent warning states: "CAUTION – SURFACE OF UNIT IS HOT WHEN ON!"

Contact Information:

• Email: support@SHARNDY.com
• Website: www.sharndy.com

Sharndy ETW13C Specifications

General

Brand	Sharndy
Model	ETW13C
Category	Indoor Furnishing
Language	English