Sharp GF-9090H User Manual

DISASSEMBLY
OPERATION
ON
MAINS
A->|BE={C {DFE | GF-9090H, HB
™
Before
operating
the
unit
on
mains,
check
the
pre-set
[A] FRONT CABINET REMOVAL (Refer to Figures 2 and 3)
1. Pull out the power cord plug or adaptor plug from the unit.
2. Take out the cassette tape from the cassette holder.
3. Remove the battery compartment lid and eight (8) bat-
teries from the battery compartment.
. Remove eight (8) screws retaining the front cabinet.
5. Gently pull out the front cabinet and disconnect four (4)
tips (Speaker) connected to the main P.W. board.
-
voltage. If the voltage is different from your local voltage,
adjust
the
voltage
as
follows:
Rotate
the
plug
of
the
voltage
selector
by
using
a
screwdriver
so
that
your
local
voltage
number can be seen. (Refer to Figure 6)
GF-9090E
Switch the mains power switch to the “ON” position.
® When the unit is used on batteries, pull out the mains
B|
OPERATION
PANEL
REMOVAL
(Refer
to
Figure
2)
plug
from
the
unit.
Otherwise
switch
off
at
the
mains
SWITGh
1.
Remove
the
front
cabinet
as
described
in
front
cabinet
power
switch
after
use.
(Refer
to
Figure
6)
GF-
9090E
removal.
Figure
2
Figure
6
2.
Remove
six
(6)
knobs
(VOLUME,
BALANCE,
TREBLE,
DIAL CORD STRINGING
(Refer to Figure 7)
BASS
and
RECORD).
|
.
Remove
four
(4)
screws
retaining
the
operation
panel.
4. Gently
lift
up
the
operation
panel
from
the
back
cabinet.
Ww
[(C]
DIAL
SCALE PLATE
REMOVAL
(Refer
to
Figure
3)
1.
Remove
the
operation
panel
as
described
in
operation
panel
removal.
2.
Remove
four
(4)
screws
retaining
the
dial
scale
plate.
3.
Gently
pull
out
the
dial
scale
plate
from
the
chassis.
DIAL POINTER
PULLEY
[D]
MECHANISM
BLOCK
REMOVAL
(Refer
to
Figure
4)
1.
Remove
the
dial
scale
plate
as
described
in
dial
scale
plate
removal.
2.
Disconnect
the
tip
(Muting)
and
two
(2)
sockets
(SO2,
$0501)
connected
to
the
main
P.W.
board
and
the
motor
P.W.
board.
3.
Remove
four
(4)
screws
retaining
the
mechanism
block.
4.
Gently
pull
out
the
mechanism
block
form
the
back
cabinet.
PULLEY
[E]
CHASSIS
(P.W.B.)
REMOVAL
(Refer
to
Figure
5)
1.
Remove
the
mechanism
block
as
described
in
mechanism
block
removal.
2. Remove the tuning knob from the tuning shaft.
3.
Disconnect
two
(2)
tips
(Antenna)
connected
to
the
main
TUNING
SHAFT
P.W.
board.
4.
Remove
six
(6)
screws
retaining
the
chassis
(P.W.B.).
5.
Gently
pull
out
the
chassis
(P.W.B.)
from
the
back
cabinet.
enWs Li)
OY)
Ay _———/
Zo
ae = a
Figure 5 Figure 7

Sharp GF-9090H Specifications

General

Brand	Sharp
Model	GF-9090H
Category	Stereo System
Language	English