Watching TV
Perform the following steps before you press POWER
on the remote control unit.
1 Insert the batteries into the remote control unit.
(See page 8.)
2 Connect the antenna cable to the TV. (See page
12.)
3 Plug in the AC cord to the AC outlet. (See page 7.)
Press POWER on the TV, or POWER on the remote
control.
TV status indicator (POWER)
ON Lighting (Green)
OFF/Standby Lighting (Red)
• POWER indicator (Green): The TV is on. ("Please wait"
will appear for a few seconds on the screen.)
i ,i¸i¸il¸:i
!i_!_ilii!i,!ii!_iiiii_il!i__,'_!i_!_'_i!!!;i,_i!_!_i!i_!_!_ii,_i!_!_;_ii_i_!_i__i!_!i_ili!_i_i,__!_iii_i!i'_!_i____i_;__i_i_!!ii,_i!_!_i!i_!_!_ii,_i!_!_i!i_!_!_;i,_i!_!_i!i_!_!_ii,_i!_!_;_'i_ili_i!iii!i_!__i__iii_iii_'_!_Ii_ii_!;i_,_;J__i_i!_i_,il!!_il!i_!_!_ii,_i!_!_i!i_!_!_;_,_i!_!_i!i_!_!_ii,_i_i!ii_ii_i_i!ii,i_!_il!i_!_!i!i!i_ili_i_!!_ii_ii_i!,_!ii_i_iii_iiii_!i_!i_ill_i_i_i!i_!i;!i,i_i_!;i_i!i_ili_!_,i_i_!;i_i!i_ili_!_,i_i_!;i_i!i_ili_!_,i_i_i!!i!!ii'ii_ii!_i_iiiiii!_i_iiiiliiiiiiiiiiiij_ii_i_i_!!!,i_i_i_iii_ii_i!!i_,!_i_i_iii_ii_i!!i_,!_i_i_iii_ii_i!!i_,!_i_i_iii_ii_i!!i_,!_i_i_iii_ii_i!_
Press POWER on the TV, or POWER on the remote
control.
• The TV enters standby mode and the image on the screen
disappears.
• The POWER indicator on the TV changes to Red.
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when POWER
is turned off.
You can change channels in several ways.
Method 1
Using CH ^/v on the remote control unit or on the
TV.
• If your cable-TV system includes analog and digital
channels using the same channel number, your channel
up function will scroll through the analog channel first,
then the digital channel. Although it may appear as though
the channel does not change, it actually moves from the
analog to the digital channel in sequence.
If you use channel-down, it will move in reverse, from the
digital channel to the analog channel.
Method 2
Using remote control buttons 0-9, • (DOT) to select
channels for VH F/UHF/CATV/DIG ITAL.
To select a 1 or 2-digitchannelnumber(e. g., Channel 5):
Press 5
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made
if there is no operation within a few seconds.
To selecta 3-digitchannel number(e. g., Channel 115):
Press 1-el-e5
To select a 4-digit channel number (e. g., Channel 22.1):
Press 2-->2-->° (DOT) -->1
• When you enter 0-9 only, channel selection will be made
if there is no operation within a few seconds.
• If you press 0 by itself in "Air" reception, nothing will
happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection wil!
be made if there is no operation within a few seconds.
Auto Ch Memory makes the TV look for all channels
viewable in the set area.
1 Press MENU and the MENU screen displays.
3
4
5
6
Press A/v to select "Channel", then press _ or ENTER.
Press A/T to select "Auto Ch Memory", then press _ or
ENTER.
Press A/v to select "Signal Type".
Press _/_ to select "Air" or "Cable".
Air VHF/UHF channels
Cab e CABLE TV channe s
Press A/T to select "Automatic Search", then press
ENTER.
The TV will begin memorizing all the channels available
in your area.
• It may take from 15 minutes to 30 minutes to complete
memorizing digital cable channels.
Depending on the reception condition, a BAR display
may not advance for several minutes, please be
patient.
• Memorizing channels is best accomplished during
evening "PRIMETIME" hours, as more stations are
broadcasting digital signals. Memorizing channels can
only be accomplished while a station is broadcasting a
digital signal to set that channel into memory.
• New digital channels may be added to your area
periodically, it is recommended to perform the "Automatic
Search" procedure regularly.
Press DISPLAY to display the current channel (or
input source) information on the screen.
When the TV receives a digital signal, the digital information
will appear for a few seconds.
• Channel number • Station name
• Channel label (if preset) • Broadcast program name
• V-Chip rating • Signal type
• Sleep timer • Audio language
• Program guide • Picture size
• Resolution
When the TV receives a analog signal, the analog
information will appear.
• Channel number
• V-Chip rating
• Sleep timer
• Picture size
• Channel label (if preset)
• Signal type
• Audioinformation (Stereoor SAP)
• Resolution
_-14
To Next Page
Loading...
Need help?
General
