MX3500N SIMULATION 7 – 39
26-69
Purpose
Setting
Function (Purpose)
Used to set whether the toner preparation
message and the toner near end message
are displayed or not when the toner quan-
tity reaches 25%.
Section
Process
Item
Specifications
Operation/Procedure
[The items which can be set by this simulation]
• Used to set whether the toner preparation message is displayed
or not when the toner remaining quantity reaches 25% (set by
item A).
• Used to set whether the toner near end message is displayed or
not when the toner remaining quantity reaches toner near end
(set by item B).
• Used to set whether the machine operation is allowed or not
when the toner remaining quantity reaches toner end (set by item
C).
• Used to set whether the toner near end message is displayed
and to set what number of sheets can be outputted (copy/print/
FAX) when the toner remaining quantity reaches toner near end
message with the set item B set to "0." (The set range is 0 - 200
sheets (set by item D)).
1) Select an item to be set with [↑] and [↓] buttons.
2) Enter the set value with 10-key.
3) When [OK] button is pressed, the current set value is set.
* When [↑], [↓] button, [COLOR], or [BLACK] key is pressed,
the current set value is saved to EEPROM and RAM.
<Setting range and default value of each value>
* The numbers of printable sheets specified above are calculated
with A4 paper and print ratio 5% (The numbers, therefore, differ
depending on the paper size and the print ratio.).
NOTE: When the set item B is set to "0" and the toner remaining
quantity reaches toner near end, the toner near end mes-
sage is displayed and the number of sheet set in item D
can be outputted (copy/print/FAX). During this operation,
insufficient density, blur, and failed color balance may be
resulted depending on the user conditions.
To prevent against occurrence of those symptoms, set the
set item D to "1." When the toner remaining quantity
reaches toner near end, the toner near end display is not
displayed and the toner end display is shown to disable
copy/print/FAX, and toner cartridge replace is required.
27
27-1
Purpose
Operation test/Check
Function (Purpose)
Used to set whether the detection of com-
munication error with RIC (U7-00) is dis-
abled or not.
Section
Communication (RIC/MODEM)
Item
Specifications (Operation mode)
Operation/Procedure
1) When the machine enters Simulation 27-01, following the
screen is displayed.
2) Enter the set value with 10-key.
3) When [OK] button is pressed, and the current set value is
saved to EEPROM and RAM.
After completion of setting, [OK] button returns to the normal
display.
* When [OK] button, [COLOR], or [BLACK] key is pressed, the
current set value is saved to EEPROM and RAM.
<Setting range and default value of each value>
Display item Content
Set
range
Initial
value
A TONER PREPA
RATION
(0:YESS 1:NO)
0 The toner preparation
message is displayed.
0 to 1 0
1 The toner preparation
message is not displayed.
BTONER
NEAREND
(0:YESS 1:NO)
0 The toner near end message
is displayed.
0 to 1 0
1 The toner near end message
is not displayed.
C TONER END 1 Operation enabled at
TONER END
1 to 3 3
2 Operation disabled at
TONER END
3 Operation disabled at
TONER END
D TONER END
COUNT
1 0 sheet printable after
TONER NEAR END *
1 to 5 3
2 25 sheets printable after
TONER NEAR END *
3 50 sheets printable after
TONER NEAR END *
4 100 sheets printable after
TONER NEAR END *
5 200 sheets printable after
TONER NEAR END *
CLOSE
0
A:
A: 1
B: 0
C: 0
D: 0
; GMT
±:-
; GMT HOUR
; GMT MINUTE
; INTERNET: YES
SIMULATION NO.26-67
SUMMER TIME&TIME ZONE ADJUSTMENT
1
[0~1]
OK
TEST
TIME ZONE
SUMMER TIME
Item Display Content
Setting
range
Default
value
A DISABLE 0: YES (U7-00) Not
detected
YES 0 to 1 0 0: Not
detected
1: NO NO 1
To Next Page
Loading...
