MX3500N SIMULATION 7 – 114
If there is any item under [↓], an active display is made and
item is shifted.
If there is no item over [↓], the display grays out and the
operation is invalid.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3) When [OK], [↑], [↓] button, [COLOR], or [BLACK] key is
pressed, the current set value is saved to EEPROM and RAM.
<Set range and default value of each set value>
When the value of transfer ON/OFF timing is decreased, the trans-
fer ON/Off timing for paper is advanced.
When the value of transfer ON/OFF timing is increased, the trans-
fer ON/Off timing for paper is delayed.
(±1: about 10ms change)(Set range: –490 to +490ms)
51-2
Purpose
Adjustment
Function (Purpose)
Used to adjust the contact pressure of
paper against the registration roller (main
unit paper feed section, duplex paper feed,
RSPF/DSPF paper feed) on each section.
(When there are much variations in print
image positions for paper or when the
paper jam occurs, the adjustment is
required.) Used to change the deflection
quantity correction value of each specified
cassette.
Section
Paper transport
Item
Operation
Operation/Procedure
1) Select a category to be set. (In this example, [SIDE1] is
selected.)
* Select a category, and the selected button is highlighted.
The set item of the selected category button is displayed.
* Only one button can be selected. The selected button is
highlighted.
* Select the set item with [↑] and [↓] buttons.
The highlighted section of the set value is switched and dis-
played on the set setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and the
operation is invalid.
If there is any item under [↓], an active display is made and
item is shifted.
If there is no item over [↓], the display grays out and the
operation is invalid.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3) When [OK], [↑], [↓] button, [COLOR], or [BLACK] key is
pressed, the current entered value is saved to EEPROM and
RAM.
* When [CLOSE] button is pressed, the display shifts to the
copy basic screen of simulation.
* Copying can be performed also by pressing [COLOR]/
[BLACK] key.
<Set range and default value of each set value> * RSPF model
Item Display item
Description of
content
Set
range
Default
value
A TC2 ON TIMING Secondary transfer
voltage ON timing
setting
1 to 99 40
B TC2 OFF TIMING Secondary transfer
voltage OFF timing
setting
1 to 99 60
0
:
A㧦 99
B㧦 60
㧧 TC2 ON TIMING
㧧 TC2 OFF TIMING
SIMULATION
NO.51
㧙
01
TRANSCRIPTION TIMING SETUP
99
㨇
1
㨪
99
㨉
TEST
CLOSE
OK
Item Button Display item
Description of item (Mode, document, paper feed
speed)
Transport direction
Set
range
Default
value
A SIDE1 NORMAL_PLAIN_HIGH RSPF front surface document, deflection quantity
adjustment value (normal, plain paper, HIGH)
–1 to 9950
B NORMAL_PLAIN_LOW RSPF front surface document, deflection quantity
adjustment value (normal, plain paper, LOW)
–1 to 9950
C NORMAL_ THIN _HIGH RSPF front surface document, deflection quantity
adjustment value (normal, thin paper, HIGH)
–1 to 9950
D NORMAL__THIN LOW RSPF front surface document, deflection quantity
adjustment value (normal, thin paper, LOW)
–1 to 9950
E RANDOM_PLAIN_LOW RSPF front surface document, deflection quantity
adjustment value (random, plain paper, LOW)
–1 to 9950
F RANDOM_ THIN _LOW RSPF front surface document, deflection quantity
adjustment value (random, thin paper, LOW)
–1 to 9950
A SIDE2 NORMAL_PLAIN_HIGH_1 RSPF back surface document, deflection quantity
adjustment value 1(normal, plain paper, HIGH)
–1 to 9950
B NORMAL_PLAIN_LOW_1 RSPF back surface document, deflection quantity
adjustment value 1(normal, plain paper, LOW)
–1 to 9950
C NORMAL_PLAIN_HIGH_2 RSPF back surface document, deflection quantity
adjustment value 2(normal, plain paper, HIGH)
–1 to 9950
D NORMAL_PLAIN_LOW_2 RSPF back surface document, deflection quantity
adjustment value 2(normal, plain paper, LOW)
–1 to 9950
To Next Page
Loading...
