Sharp MX-3500N

MX3500N OTHERS 12 – 3
Customize 3 Quick File
USB Memory Scan
Customize 1 Special Modes
Customize 2 Erase
Customize 3 Suppress BG
Data Entry
Customize 1 Special Modes
Customize 2 File
Customize 3 Quick File
Device Control
Original Size Detector Setting
Original Detection Size
Combination
Varies depending on
country and region
Cancel Detection at Document
Glass
Disable
Disabling of Document Feeder*3 Disable
Original Feeding Mode*3 All Disabled
Disabling of Duplex Disable
Disabling of Large Capacity
Cassette*7
Disable
Disabling of Optional Paper Drawer*8 Disable
Disabling of Tray Setting Disable
Disabling of Finisher*9 Disable
Disabling of Offset Disable
Disabling of Stapler*9 Disable
Saddle Stitch Position Adjust*10 0.0 mm
Disabling of Punch*11 Disable
Disabling of Colour Mode*12 Disable
Auto Paper Selection Setting Plain Paper
Registration Adjustment
Auto Adjustment -
Optimization of the Hard Disk -
Tandem Connection Setting
IP Address of Slave Machine 0.0.0.0
Port Number 50001
Disabling of Master Machine Mode Disable
Disabling of Slave Machine Mode Disable
Clear All Job Log Data -
Detect Standard in Auto Colour Mode 3
Copy Settings
Initial Status Settings
Colour Mode Auto
Paper Tray Varies depending on the
machine configuration
Exposure Type Auto
Copy Ratio 1
2-Sided Copy 1-Side to 1-Side
Output -
Exposure Adjustment
Colour
Document Glass 5
Document Feeder 5
B/W
Document Glass 5
Document Feeder 5
Rotation Copy Setting Enable
Add or Change Extra Preset Ratios
Reduction -
Enlargement -
Setting a Maximum Number of Copies 999
Initial Margin Shift Setting
Side-1 10 mm (1/2")
Side-2
Erase Width Adjustment
Edge 10 mm (1/2")
Centre
Card Shot Settings
Original Size X: 86 mm (3-3/8") Y: 54
mm (2-1/8")
Fit to Page Disable
Automatic Saddle Stitch*10 Enable
Initial Tab Copy Setting 10 mm (1/2")
Item Factory default setting
Disabling Deletion of Job Programs Disable
Disabling of Bypass-Tray in Duplex
Copy
Disable
Disabling of Auto Paper Selection Disable
Auto Selection Setting of Tray that is
Supplied the Paper
Disable
Initial Colour Balance Setting Factory Default State
Auto Colour Calibration -
B/W 600dpi x 600dpi Scanning Mode
for Document Feeder*3
Disable
B/W Quick Scan from Document Glass Enable
Network Settings
IP Address Setting DHCP
Enable TCP/IP Enable
Enable NetWare Enable
Enable EtherTalk Enable
Enable NetBEUI Enable
Reset the NIC -
Ping Command -
Printer Settings
Default Settings
Prohibit Notice Page Printing Enable
Prohibit Test Page Printing Disable
A4/Letter Size Auto Change Varies depending on
country and region.
Print Density Level
Colour 3
B/W 3
Bypass Tray Settings
Enable Detected Paper Size in
Bypass Tray
Disable
Enable Selected Paper Type in
Bypass Tray
Enable
Exclude Bypass-Tray from Auto
Paper Select
Disable
Job Spool Queuing Enable
Interface Settings
Hexadecimal Dump Mode*1 Disable
I/O Timeout 20 sec.
Enable USB Port Enable
USB Port Emulation Switching*1 PCL (Auto*13)
Enable Network Port Enable
Network Port Emulation
Switching*1
PCL (Auto*13)
Port Switching Method Switch at End of Job
Colour Adjustments
Auto Colour Calibration -
Image Send Settings*14
Operation Settings
Default Display Setting
Mode Scanner*4 (Fax*6)
Hold settings for a while after
scanning has been completed
Disable
Switch Automatically to Copy
Mode Screen
Disable
Initial Resolution Setting
Apply the Resolution Set when
Stored
Disable
Scanner*4 200x200dpi
Internet Fax*5 200x100dpi
Fax*6 Standard
Default Exposure Settings
Exposure Auto
Original Image Type Text
Disable
Must Input Next Address Key at
Broadcast Setting
Disable
Scan Complete Sound Setting Middle
The Number of File Name/Subject/
Body Keys Displayed Setting
6
The Number of Direct Address
Keys Displayed Setting
6
Item Factory default setting