Parts and functions
The handwriting pad is set to enter characters when the cursor is in
any part of the character entry area.
Single-frame pad
Dual-frame pad
Insert the batteries using the procedure below before using the
PW-AT760 for the rst time.
To insert the batteries
1
Set the battery replacement switch on
the bottom of the unit to the “
解除( 交
換時 )
” position.
2
Remove the battery cover as shown
in the diagram.
3
Insert the batteries included with the
unit.
Make sure the battery polarity is correct.
• Insert the batteries over the ribbon
tab being sure not to cover the end
of the tab.
4
Replace the battery cover as shown in
the diagram.
5
Set the battery replacement switch to
the “
ロック( 使用時 )
” position.
6
Open the unit and press to turn
the power on.
The calibration screen
for the handwriting pad
appears.
Using the PW-AT760 for the first time
• If the power cannot be turned on:
• Make sure the battery replacement switch is in the “
ロック
( 使用時 )
” position, then press
again.
• If the power still cannot be switched on, try performing steps
1 through 6 in the above procedure again.
7
Pull out the stylus, extend it, and use it to accurately touch the
center of the “+” character displayed on the handwriting pad.
• Touch the center of “+” as it appears in four different locations.
The LCD contrast adjustment screen appears.
8
Adjust the LCD contrast of the main display using ( )
and ( ).
9
The LCD contrast of the handwriting pad can be adjusted by
touching and displayed on the pad.
Layout
ELECTRONIC DICTIONARY
PW-AT
760
QUICK REFERENCE
Global search key
(Searching through several
dictionaries is possible.)
Utility keys for dictionaries
and functions
(S-jump, quick reference, example/note,
illustrations/diagrams/notes, audio, switch,
playback setting, bookmark, word list)
Font size shift (zoom) keys
Menu (Menu customize) key
Card key
Back space (delete) key
Clear key
Card slot (side)
Page scroll keys
Volume control (side)
Cursor keys
Dictionary/function selection keys
Escape key
Search/enter (store) key
Handwriting pad
Stylus holder (side)
10
When done, press .
The key sound (beep) on/off screen appears.
11
Select or to turn the key sound on/off.
Kana input screen appears.
12
Press to select alphabet character input or press to select
Japanese input.
Entering characters using the single-frame pad
Example: Enter a Japanese word “
持つ
” in the
Japanese-English dictionary.
1
Press .
The entry/selection screen of
ジーニアス英和
&
和英辞典
appears,
with the cursor placed over the spelling entry area.
Using the handwriting pad
The handwriting pad is set to the English character entry mode.
• If the dual-frame pad is displayed, press to switch to
the single-frame pad.
2
Press to move the cursor to the Japanese entry area.
The handwriting pad is now switched to enter kanji and kana.
3
Use the stylus to draw “
持
” on the handwriting pad.
The character shown in the candidate list display area is also
placed in the entry area so that the dictionary search can proceed.
4
If the character in the entry area is not the one you desired, use
the stylus to touch and select the desired character in the list.
The character in the entry area changes.
• If you cannot nd the character in the list, touch or press
to erase it and reenter it on the pad.
{
Character entry type indicator
button
button
button
button
Candidate list display area
Writing area (frame)
Main display Handwriting pad
button
button
Automatic/manual
recognition indicator
Character entry type indicator
button
button
button
button
button
button
Entry display area
5
Likewise, enter “
つ
” in the entry area.
When you start drawing, the previous entry is conrmed then
erased.
Entering characters using the dual-frame pad
Example: Enter “
案山子( かかし )
” in
スーパー大辞林
.
1
Press .
2
Press to switch to the dual-frame pad.
3
Use the stylus to draw “
案
” on the thick-framed (undotted)
writing area.
4
If a character is recognized incorrectly, use the stylus to touch
the character. In the candidate display area, nd and touch the
character to replace it with.
5
Likewise, repeat the above steps 3 – 4 to enter “
山
” and “
子
”.
For longer words, enter up to six characters, then touch to
transfer the entries to the content’s entry eld.
6
When done entering, touch to transfer the characters to
the content’s entry eld.
You can then proceed with the
dictionary search.
button
Writing area (frames)
Candidate list display area
Automatic/manual
recognition indicator
Upon completion of each entry, the positions
of these two areas switch automatically. The
dotted-framed side cannot accept entries.
• To have the dictionary recognize the entry
immediately, touch on the pad.
dotted
frame
The character in the entry display area is
replaced with the character selected in the
candidate display.
Up to 6 characters
can be accomodated.
back of the unit
To Next Page
Need help?
General
