Sharp ZQ-3000 - Page 5

10.
Using
the
data
transfer
function
This
Organizer
can
transmit
data
to
and
receive
data
from
the
follow-
ing products.
1,
Data
transfer
between
ZQ-3000
series
Organizers
(using option
CE-200L
or CE-300L).
2,
Data
transfer
with
a
ZQ-5000
or
IQ
series
Organizer
(using
option
CE-200L
or
CE-3O00L).
3.
Data
transfer
with
an
EL
series
Organizer
(including
Auto
Dialer)
that
has
data
transfer
capability
(using option
CE-2207).
Before
establishing
communication
between
products,
turn
the
products off and connect the cable.
Notes:
© To interrupt data transfer, press
©
If
a
connector
is
disconnected,
or
a
similar
problem
occurs
during
data
transfer,
the
message
"/O
DEVICE
ERROR’
wilt
appear.
*
After
data
transfer,
the
data
on
the
transmitter
is
preserved.
10-1.
Transferring
data
between
ZQ-3000
series
Organizers
Telephone
directory data,
schedule
data,
and
memo
data
can
be
transferred.
Data
can
be
transferred
and
verified
by
mode
{all
items
in
the
SCHEDULE
mode,
MEMO
mode,
or
a
telephone
directory
—
TEL,
TEL2,
TEL3)
or
by
data
item.
In
addition,
data
can
be
backed
up
using
Organizers
of
the
same
type.
Transferring
data
by
mode
and
by
data
item
Schedule
data
are
transferred
by
mode.
During
mode
transfer,
data
previously
stored
in
the
specified
mode
of
the
receiver
are
deleted.
Proceed
with
a
caution.
Note:
When
mode
transfer
is
carried
out
in
the
telephone
directory
mode,
all
listings
in
the
directory
will
be
transferred.
(In
this
case,
the
directory
name
is
transferred
at
the
same
time.)
4. Select the mode on the transmitter and receiver.
SCHEDULE (Transmitter)
SCHEDULE] (Receiver)
2. Select the data transfer function on the receiver.
UNIT TO UNIT
SEND
RECEIVE
VERIFY
3, Select the receiver in the receive mode.
2
UNIT TO UNIT
RECEIVING
MODE |
4.
Select
the
data
transfer
function
on
ihe
transmitter.
UNIT TO UNIT
SEND
RECEIVE
VERIFY
Note:
When
transferring
by
data
item,
display
the
desired
data
and press[2nd] [OPTION ].
ES
ZQ-3250
5, Perform data transfer.
|
Notes:
® |f the mode of the transmitter and the mode of the receiver are not
the same, data transfer is not established. The message “DATA
ERROR"* is displayed.
When telephone directory data are transferred, directories on the
transmitter and receiver can be different. However, the contents
received by the receiver will be stored in the open directory. For
example, if data transfer is established between file TEL1 in the
transmitter and file TELS in the receiver, then the contents of TEL1
will be sent to and stored in TELS.
*® Tur off the secret function on both the transmitter and the
receiver before mode transfer.
® If the amount of memory available on the receiver at the time of
transfer is insufficient, data transfer is not possible. The message
“MEMORY FULL" appears. Delete any unnecessary data, verify
whether the available memory is sufficient, and repeat the data
transfer procedure.
Transferring backup data
All the contents of the Organizer are transferred. During backup data
transfer, data stored on the receiver are deleted. Proceed with cau-
tion.
(Backup data transfer is only possible between identical products.)
1. Select the data transfer function on the receiver and set it in the
receive mode for backup data transfer.
2
,
UNIT
TO
UNIT
BACKUP
RECEIVING
MODE
2. Select the data transfer function on the transmitter and perform
backup data transfer.
1Y
Verifying data
It is possible to verify data by mode or by data item. If any discrepan-
cies are found, the message “VERIFY ERROR" is displayed.
Verify data in the SCHEDULE mode.
1. Select the mode on the transmitter and the receiver.
SCHEDULE (Transmitter)
SCHEDULE] (Receiver)
2. Set the receiver in the verify mode.
OPTION] 3
UNIT TO UNIT
-VERIFYING-
3. Select the data transfer function on the transmitter.
Note: To verify one data item, display the data item to be verified and
press
[2nd] [OPTION] -
4. Perform verification.
1