Sharp ZQ-3000 - Page 6

ZQ-3250
10-2.
Transferring
data
witha
20-5000
or
IQ
series
Organizer
Telephone
directory
data,
schedule
data,
and
memo
data
can
be
transferred.
Data
can
be
transferred
and
verified
by.
mode
and
by
data
item:
Note:
When.
mode
transfer
is
carried
out
in
the
fesicna:
direcotry
_
mode,
all
listings..in
the
directory
will
be
transferred.
(In.
this
speeey
the
directory
t
name
is
transferred:
at
‘the
same
ime.
)
Transferring data by mode and by data iter.
Transfer the “ABC BANK* memo data stored i in the Organizer.
1. = the data in the transmitter to be transferred.
re
To
perform
mode
transfer,
selact
the
mode
by
pressing
‘the
“mode key, and then press. It is not necoseaty, to
~ display the data. ay ee
2.
Select
the
data
transter
function
on
|
the
receiver,
and
set
the
receiver
in
the
receive
mode.
;
;
3.
‘Select
the
data
transfer:
Meictien:
on
the
transmitter
schea
d-pertorm
‘data
transfer.
©
ieee
[2nd] [OPTION] 1 _
Note:
Follow
the
same
steps
to
transfer
data
from
a
Za.
5000
or
1a
series
Organizer.
Verification
Follow
the
steps
explained
in
"Transferring
data
between
ZQ-3000
series Organizers" above.
10-3.
Transferring
data
with
an
EL
series
Organizer
(including
Auto
Dialer)
Telephone
directory
data
and
schedule
data
can
be
transferred:
(For
the
Auto
Dialer
only
the
telephone
direcory
data
can
be
transferred.)
Data
can
be
transferred
by
mode
and
by
data
item.
When
transferring
data
with
an
EL
series
Organizer,
the
following
restrictions
apply:
*
When
transferring
data
to
an
EL
series
Organizer:
Transferred
data
are
added
to the
data
previously
stored.
Data
are
transferred
in
the
same
mode
and
directory.
lf
the
transferred
data
item
exceeds
the
maximum
number
of char-
acters
that
can
be
entered
into
the
El.
series
Organizer
as
one
data
item,
excess
characters
are
deleted.
Characters
and
symbols
that
cannot
be
displayed
on
the
EL
series
Organizer are replaced by spaces. If all the columns that can be:
displayed are replaced by spaces, the correspanding data item is
not stored.
All received letters are converted to capital letiers.
If the secret function is turned on in the Organizer, only non-secret
data are trarisféerred.
* When transferring data from an EL series Organizer:
The
received
data
are
added
to
the
data
previously
stored.
When receiving. non-English characters, all characters are con-
verted to small letters.
If the secret function is turned on in the EL series Organizer, only
non-secreit data are transferred.
Transferring
data
to-an
EL
series
Organizer.
.
ni
Transfer
all
TEL1
data
ii
the
‘Organizer
to
TEL!
in
the
EL
Séjiés
Organizer.
.
.
.
1.
Set
thé
recéiver
in
the
receive
mode.
2.
Select
the
made
on
the
transmitter.
_
TEL
|
Since
telephone
directory
data
is
being
transferred,
‘select
the
file.
3.
Select
the
data
transfer
function
on
the
transmitter.
‘(nal [OPTION]
Note:
To
transfer
one
data
item,
disp
la
the
data
iter
to
be
traris-
ferred and press [2nd] ran
4. Perform data transfer.
*
|f
the
arnount
of
memory
available
in:
‘the.
receiver
at
the
time
of
data
transfer
is‘
insufficient;
an
error
message
appears.
Delete
any
unnecessary
data,
verify
that
there
is
sufficient
memory
available,
and
Tapeat
the
Process.
Transferring
data
from’:
an
EL
series
Organizer
1.
Select
the
mode
on
the
receiver.
2.
Select
the
data
transfer
function.on
the
receiver,
and:
set
the
receiver in the receive mode.
3. Perform data transfer from thet transmitter. ;
11.
When
trouble:
7
An
impact
or
a
strong
exieral
electrical
field
may
iseve
none
Ma
the
keys
operational.
Press
the
RESET
switch
on
the
back
of
the
Or-
ganizer.
The
impact
or
external
eects
field
may
erase
some
or
all
of
ithe
Organizer’s
memory.
-
Press
the
RESET
switch
with
the
tip
of
a
ball-point
pen
or
similar
object,
but
not
anything
breakable
(like
a
pencil
point
or
a
needle).
All RESET operation
If
a
problem
occurs
after
replacing
the
batteries,
or
if
the
Organizer
does
not
function
properly
even
after
the
above
RESET
operation,
perform
the
following:
1.
While
holding
[ON],
press
the
RESET
switch
on
the
back.
Release
the
RESET
switch
and
then
release
[ON].
The following display will appear.
DATA
ALL CLEAR
2. Press [_N_]
Returns to the initial display.
Caution:
Do
not
press
Lyi
in
step
2.
Pressing
[¥..
LY¥._]
wil
~"
deléte
all-data
and
teset
the
clock.’
.