Programming remotes in
1. Default the unit before you begin a new installation. This erases all previously programmed remotes.
2. Press the LEARN switch once to step to relay 1. (1 x beep sounds)
3. Press the button on the remote control a few times to learn in to the RX4-500 (2x beeps sound)
4. Continue to learn in any additional remote controls until all the remotes are programmed in.
5. Press the LEARN switch again to step to relay 2. (1x beep sounds)
6. Repeat Step 3; 4 & 5 until all the remotes are programmed in to each respective relay.
7. Once Relay 4 is programmed, press the LEARN switch once more to step past relay 4 and exit out
of learn mode. (1 x long beep sounds)
Note: The unit can be programmed with up to 80 remotes. When the memory limit has reached its limit the
RX1-500 will auto exit out of program mode. The unit auto exits out of program mode if nothing is received after
10 -20 seconds.
Code-Hopping Encryption
1 x Relay output
Normally Open / Closed
Weather-proof ABS housing
Frequency stability controlled +/- 75KHz
Order Codes:
This product is approved for use in residential, commercial andlight
Industrial environment and complies with the essential protection
requirements of the R&TTE Directive 1999/EC on the
approximation of the laws of the Member states relating to
electromagnetic compatibility and radio spectrum.
Certifications:
ETSI EN300 220-V2.4.1
ETSI EN301-489-3 V1.4.1
ETSI EN301-489-1 V1.9.2
IEC 60950-1:2005 + A1:2009
Model No: RX1-500
1 Channel Receiver : 500m Code Hopping
Approvals: * (pending)
Installation Instructions - For Service Persons Only
III
Model:
Encryption type:
Transmission frequency:
Transmission method:
Modulation
Transmission range:
Memory capacity:
Voltage range:
Standby current consumption:
Current consumption all on:
Operating Temperature:
Dimension (lxbxh)
Gross weight:
RX1-500
Code hopping
403MHz (local) 433MHz (export)
OOK
AM
500m “Line of sight”
80 remotes
10V to 16VDC
+/-22mA 10%
+/-126mA 10%
-3°C to 49°C
145 x 66 x 40mm
135g
Technical Specifications:
Features:
For more info visit our web site: www.sherlotronics.com
1 Channel Receiver : 500m Code-hopping
RX1-500
English
Warranty
This product is sold subject to our standard warranty conditions and is warrantied against defects in workmanship
for a period of two years.
Customer Support line: +2711 462 5101 E-mail: technical@sherlotronics.co.za
LEARN
Press and hold for more than
10 Seconds. When the beeping
stops the unit is defaulted.
Wait a few seconds until it re-boots.
Note: Please default the unit first before installation.
This will erase any previously programmed factory
test remotes from the memory.
Defaulting the RX4-500
Relay time jumper settings
Programming the ON/OFF function
1. Default the unit before you begin a new installation. This erases all previously programmed remotes.
2. Select the 1 sec & 3 sec relay time jumpers respectively.
3. Press the LEARN switch once to step to relay 1 (ON command) (1 x beep sounds)
4. Press the button on the remote control for the ON command. (2 x short beeps sound)
5. Press the LEARN switch again to advance to the OFF command. (2 x beep sounds)
6. Press the button on the remote control for the OFF command. (2 x short beeps sound)
7. Press the LEARN switch again to advance to the next relay channel.
8. Repeat Step 3 - 6 until all the remotes are programmed in to each respective relay.
7. Once Relay 4 is programmed, press the LEARN switch once more to step past relay 4 and exit out
of learn mode. (1 x long beep sounds)
3 Seconds
Gate &
garage door
automation
Panic
on alarm
panel
Maglock
release /
beam bypass
Arming &
Disarming
alarm panels
1 Second
Latch/un-Latch
On / Off
Code 1 = ON
Code 2 = OFF
60 Seconds
Siren output
or beam
bypass
1sec
3sec
Latch
1min
3min
On/Off
1sec
3sec
Latch
1min
3min
On/Off
1sec
3sec
Latch
1min
3min
On/Off
3 Min
1sec
3sec
Latch
1min
3min
On/Off
1sec
3sec
Latch
1min
3min
On/Off
1sec
3sec
Latch
1min
3min
On/Off
Erasing individual remotes
1. Link the ERASE jumper
2. Press the LEARN switch
3. Press the remote to be erased
4. Repeat step 2 & 3 for each
remote to be erased.
5. Remove ERASE jumper when
done
Press the button
to be erased
Repeat for each remote
to be erased.
You must erase
one remote
at a time.
20 beeps
LEARN
ERASE
Link On
To Next Page
Need help?
General