ShiftCam ProGrip - ShiftCam ProGrip User Manual; ShiftCam Warranty Information; Important Safety Instructions; Battery and Power Specifications

Legal and CompliancePart III
15
User ManualPart II
14
FCC Statement:
Declaraon of Conformity with
FCC Rules for Electromagnec
Compability
We ShiCam Limited, declare under
our sole responsibility that the product
PG0001 to which this declaraon
relates, complies with Part 15 of the
FCC Rules. Operaon is subject to the
following two condions: (1) this device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operaon.
protecon against harmful interference
in a residenal installaon.
This equipment generates, uses, and
can radiate radio frequency energy,
and if not installed and used in
accordance with the instrucons, may
cause harmful interference to radio
communicaons. However, there is
no guarantee that interference will
not occur in a parcular installaon.
If this equipment does cause harmful
interference to radio or television
recepon, which can be determined by
turning the equipment o and on, the
user is encouraged to try and correct
the interference by one or more of the
following measures:
Federal Communicaon Commission
Interference Statement
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits
are designed to provide reasonable
FCC Cauon
Any changes or modicaons not
expressly approved by the party
responsible for compliance could void
the user’s authority to operate this
equipment.
Radiaon Exposure Statement
This equipment complies with FCC
radiaon exposure limits set forth for
an uncontrolled environment. End
users must follow the specic operang
instrucons for sasfying RF exposure
compliance. To maintain compliance
with FCC RF exposure compliance
requirements, please follow operaon
instrucons as documented in this
manual. This equipment should be
installed and operated with a minimum
distance of 20 cm between the radiator
and your body.
ShiCam ProGrip
Regulator Compliance
Information
Reorient or relocate the receiving
antenna
Increase the distance between the
equipment and the receiver
Connect the equipment to an outlet
on a circuit dierent from that to
which the receiver is connected
Consult the dealer or an experienced
radio/TV technician for help
Need Assistance?
Got a queson about our products?
Scan the QR code to submit an enquiry,
or email us at cs@shicam.com and we
would be happy to assist you.
Happy shoong!
To learn more about ShiCam, visit our
ocial website at ShiCam.com
Aaching ProGrip to
Your Smartphone
Checking ProGrip’s Baery
Power Level
Align your smartphone to the center
of the clamp, indicated by the
markings on the clamp arms
Push down the lower arm with your
smartphone to open up the clamp
Push your smartphone into the top
arm and release the clamp to secure
To release your smartphone from
ProGrip, open the clamp and remove
your smartphone
Press the shuer buon on ProGrip.
The blinking blue LED indicates
pairing mode is acve.
Turn on the bluetooth pairing
on your smartphone and select
“ShiCam ProGrip” to pair
A solid blue LED light indicates
successful pairing
Click and shoot on your mobile using
the shuer buon
Press the bluetooth buon and hold
for 3 seconds to reset bluetooth
Blue LED light will start blinking,
indicang bluetooth is in pairing
mode.
The shuer buon mirrors the funcons
of the camera buon of your phone’s
primary camera app. Short press to take
photo, long press to take burst/video
Double-press the Charging Buon
White LED lights will turn o,
indicang that charging funcon has
been turned o
1)
2)
3)
4)
1)
2)
3)
4)
1)
2)
1)
2)
To aach ProGrip to your smartphone:
Connecng to Bluetooth Shuer
To connect bluetooth shuer:
To reset bluetooth:
To turn o USB-C charging funcon: width <75mm, add the Rubber In-Lay
Aachments or Silicone Stoppers
included in packaging onto the inside of
the clamp to secure.
Note: For smaller phone models with
Sleep Mode: Aer 15 mins without
pressing the shuer buon, ProGrip will
enter sleep mode. To reacvate, press
the shuer buon once
The white LED lights on ProGrip
indicates its baery level
To check ProGrip’s baery level:
Press the Charging Buon, LED light
indicang power level will appear
Hand Strap
To aach Hand Strap
Feed the end of the nylon strap from
boom up through the Hand Strap
Loop, then feed the nylon strap back
into the plasc buckle
Adjust length by pulling the nylon
strings against the plasc buckles on
top and boom of the Hand Strap
Place the Hand Strap Aachment on
the boom of ProGrip aligned with
openings, screw in knob to secure
1)
2)
3)
Cold Shoe Mount
Mounng Accessories using Cold Shoe
Mount / Cold Shoe Mount Adapter
Open the ap covering the Cold
Shoe Slot on top of ProGrip
Place the Cold Shoe Mount above
the opening then screw in knob to
secure
To adjust the angle in which the
accessory faces, add-on the rotatable
1)
2)
3)
¼” Tripod Screw
Screw in to aach accessories into
the ¼” screw thread on the boom of
ProGrip
4)
Cold Shoe Mount Adapter by sliding
it into the mount
Aach accessories of your choice to
the Cold Shoe Mount / Cold Shoe
Mount Adapter accordingly
EU Compliance Statement
ShiCam Limited hereby declares
that this product is in compliance
with the essenal requirements
and other relevant provisions of the
R&TTE Direcve and Radio Equipment
Direcve 2014/53/EU, and all other
applicable EU direcve requirements.
Qi BPP cered and compable
with EPP.
The WEEE symbol indicates that
this product must not be disposed
of with normal household waste.
When you dispose of this product you
must do so in accordance with local
environmental laws and guidelines. For
more informaon on how to dispose of
this product please contact your local
authority, disposal service, or ShiCam
Limited directly.
ShiftCam - Getting Started draft 08.indd 14-15
ShiftCam - Getting Started draft 08.indd 14-15
3/8/2022 6:46 PM
3/8/2022 6:46 PM