What to do if motor overload alarm occurs in Shini Industrial Equipment?
If you're getting a motor overload alarm on your Shini Industrial Equipment, it could be due to a blocked filter. Clean the filter and reset the overload relay. Another cause could be one of the three phases lacking. In this case, check the circuit and reset the overload relay.
Why is the material hopper still empty in my Shini Industrial Equipment?
If the material hopper in your Shini Industrial Equipment remains empty or a material shortage alarm occurs after several loading attempts, it could be due to several reasons. First, ensure the storage tank isn't empty and add material if needed. Secondly, check for air leaks in the pipe, lock it tightly, and replace the vacuuming pipe if necessary. Finally, inspect the filter for blockage and clean it if needed.
What to do if the fuse keeps burning out in Shini Industrial Equipment?
If the fuse in your Shini Industrial Equipment burns out immediately after start-up, it suggests a short circuit or a connection to the ground. To resolve this, you should check the circuit.
Why motor can't run in Shini Industrial Equipment?
If the motor of your Shini Industrial Equipment won't run, it could be due to a short-phase issue or the motor being burnt out. You should check the motor and replace it if necessary.
What to do if suction blower doesn't run in Shini Industrial Equipment?
If a shortage lasts for an extended period but the suction blower doesn't run on your Shini Industrial Equipment, the main switch and control switch might not be open or well-connected; close the main switch and control switch and check their connecting. Alternatively, the microswitch on the hopper may not be connecting properly; adjust or replace it. Finally, the signal wire could be broken; re-connect it.
What to do if the suction blower still runs when hopper is full in Shini Industrial Equipment?
If the suction blower continues to run even when the hopper is full in your Shini Industrial Equipment, it indicates that the touch point is conglutinated. You should repair or replace it.
Diagram showing the exploded assembly of the SAL-700 model components.
Comprehensive list of spare parts for the SAL-700, including part numbers and descriptions.
Diagram illustrating the exploded assembly of SAL-800G1/G2 model components.
Comprehensive list of spare parts for SAL-800G1/G2 models, including part numbers.
Diagram showing the exploded assembly of the SAL-900G1/G2 model components.
Comprehensive list of spare parts for SAL-900G1/G2 models, including part numbers.
Explains the vacuum generation and material feeding process for SAL-700G/800G.
Details the operational sequence and logic for SAL-700G/800G.
Describes the working principle and material handling for the SAL-900G.
Step-by-step guide for physically installing SAL-700G/800G series machines and connecting components.
Installation procedures and diagrams for setting up SAL-900G series machines.
Installation guidelines and connection details for the SAL-900GE series.
Installation steps and connections for the SAL-900GM series machines.
Guide to operating the SAL-700G/800G, including panel controls and basic functions.
Covers setting up functions, modes (C1-C4), parameters, and other operational configurations.
Operating instructions and control interface guide for the SAL-900G model.
Procedures for cleaning the material hopper and its internal filter to ensure optimal suction.
Instructions for cleaning the main unit, including filters and dust removal, for proper machine function.
Provides the main electric circuit diagram for the SAL-700G model.
Shows component layout and wiring connections for the SAL-700G.
Lists all electrical components used in the SAL-700G, with part numbers and specifications.
Provides the main electric circuit diagram for the SAL-800G model.
Shows component layout and wiring connections for the SAL-800G.
Lists electrical components for the SAL-800G, including part numbers and specifications.
Lists electrical components for the SAL-800G2, including part numbers and specifications.
Provides the main electric circuit diagram for the SAL-900G model.
Shows component layout and wiring connections for the SAL-900G.
Lists electrical components for the SAL-900G, including part numbers and specifications.
Lists electrical components for the SAL-900G2, including part numbers and specifications.
General| Brand | Shini |
|---|---|
| Model | SAL-G Series |
| Category | Compact Loader |
| Language | English |
To Next Page
