Shinko Denshi UF-620 - User Manual

Questions and Answers

R
Ronald DixonAug 16, 2025
Why is the displayed weight incorrect on my Shinko Denshi Accessories?
- R
  Robin AyalaAug 16, 2025
  An incorrect displayed weight on your Shinko Denshi Accessories could be due to several reasons. It may be because the balance hasn't been used for a while or has been moved. Perform a span adjustment to resolve this. Also, check the levelness before installation, ensuring the weight measuring sensors are horizontal. Finally, if the tare range is either set or not set, remove the sample from the weighing pan and zero the readout to continue the measurement.
M
Mr. Steven CampbellAug 19, 2025
What to do if nothing appears on the display of my Shinko Denshi Accessories even when powered on?
- F
  Francisco MurphyAug 19, 2025
  If nothing is appearing on the display of your Shinko Denshi Accessories, first check that the power supply is properly connected.
E
evelezAug 22, 2025
How to fix no inputs from the weight measuring sensor on Shinko Denshi Accessories?
- D
  Derek GainesAug 22, 2025
  If there are no inputs from the weight measuring sensor, check the connection between the indicator and the weight measuring sensors. Also, try turning the power on again. If the indicator is connected to the weight measuring sensors via an RS-232C cable, ensure you are using a straight cable.
B
Brenda OrtizAug 25, 2025
What to do if the weight of the sample exceeds the capacity of my Shinko Denshi Accessories?
- J
  johnstonbrookeAug 26, 2025
  If the weight of the sample is more than the capacity of your Shinko Denshi Accessories, unload the sample and weigh it in sections. Alternatively, replace the tare with a lighter one.
C
Carl MackAug 28, 2025
Why does the display flicker on my Shinko Denshi Accessories?
- C
  Christina CurtisAug 28, 2025
  The display might flicker because the weight measuring sensor is affected by external influences such as wind or vibration. Try changing the stability decision and readability settings to resolve this.
A
Alexander GilmoreAug 31, 2025
What to do if an error still exists after calibration of Shinko Denshi Accessories?
- R
  Rebekah EvansAug 31, 2025
  If an error persists after calibration, it's possible the balance was affected by external influences like wind or vibration during the calibration process. Implement measures to prevent wind and vibration, or relocate the balance to a more stable environment, and then perform the calibration again.
E
Eric DavidsonSep 3, 2025
What to do if Shinko Denshi Accessories balance is influenced by static electricity or noise?
- V
  Vickie HinesSep 3, 2025
  Turn the power on again.
P
Paula HallSep 6, 2025
Why is the mass of the weight too light for span adjustment on Shinko Denshi Accessories?
- B
  brendawoodsSep 6, 2025
  If the mass of the weight used for span adjustment is much lighter than the capacity of the weight measuring sensor, utilize a weight that is as close to the capacity as possible during span adjustment with an external weight.
T
Timothy ThomasSep 9, 2025
What to do if the display error during span adjustment exceeds 1.0% on Shinko Denshi Accessories?
- J
  Jimmy JohnsonSep 9, 2025
  If the display error during span adjustment exceeds 1.0%, verify that the correct weight was placed and that there are no other objects on the pan. Then, execute the span adjustment again.
S
Stephanie JonesSep 12, 2025
Why does the 'M' continuously flash on my Shinko Denshi Accessories?
- M
  Marco EricksonSep 12, 2025
  The continuous flashing of 'M' indicates that the balance may be affected by external influences such as wind and vibration. Take appropriate measures to prevent these influences or change the installation location of the balance.

Shinko Denshi UF-620 Specifications

General

Brand	Shinko Denshi
Model	UF-620
Category	Accessories
Language	English

Shinko Denshi UF-620 - User Manual

Table of Contents

Questions and Answers

Shinko Denshi UF-620 Specifications