Shoremaster 1007970 User Manual

SHOREMASTER.COM
SWIm RAftS
SWIm RAftS
A
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
QC Connector Bracket
1004187
-
1
T Handle
100087612
Carriage Bolt 3/8 x 1.75
100195923
Flange Nut 3/8
100180224
NUT 3/8
10018031
5
4 2
5
3
1
Failure to follow instructions may
result in personal injury and may
invalidate the applicable warranty.
Step 1. Attach the QC Connector Bracket
to the TS9 Frame with two 3/8 x 1 3/4
Carriage Bolts and two 3/8 Flange Nuts - as
shown.
Note: The QC Bracket must be bolted to the
TS9 Frame
Note: The TS9 Frame must be supported
by legs.
Step 2. Set the 9" Truss Dock onto the QC
Brackets and secure using the T-Handles.
QC Connector TS9 to Truss Dock
Instructions
Part #: 1004187
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
3 STEP LADDER FRAME LEFT
100561511
3 STEP LADDER FRAME RIGHT
100561612
Prt Ladder Step 15.0
100578533
Bolt Carriage 1/4-20 x .75 SS 304
10019501 24
1/4" NUT BRASS
100179712
5
POLY WASHER 3/8 ID X 1"OD X .093
100246926
Pin Snap 3/8 x 1.75
10003382
7
Washer Flat 3/8 SS
100259948
Nut Nyloc 3/8-16 Brass
100180529
Ladder Pivot Left
100177811 0
Ladder Pivot Right100177911 1
BOLT 3/8" x 2.0 PHILLIPS MACH SCREW
100242621 2
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
Swim Raft Rubber Anchor Hold
100109421
3 Step Pivoting Ladder
100763412
Ladder Brace
100497913
3/8 X 6-1/2 Hex Bolt
100244724
3/8" Washer
10025996
5
3/8 Nyloc Nut
100180526
3/8 X 1 Hex Bolt
10024192
7
3/8 Lock Washer
100259628
D
See 1006596 - Pivoting Ladder instructions
for assembly and operating steps.
12
6
8
6
8
9
4
3
2
1
10
5
7
11
Poly Swim Raft w/3 Step Ladder
Instructions
Part #: 1007970 - Yellow
1007980 - Grey
1024603 - Tan
5
8
7
2
3
5
6
1
4
5
Attach Ladder
Step 1. The rear of each Ladder Pivot is bolted through the
hole marked on the drawing as Hole Location. Two 3/8" x
6-1/2" bolts and two 3/8" washers are placed through the
rear of each ladder pivot. The bottoms of the two bolts are
secured through a Ladder Brace using two 3/8" washers and
two 3/8" Nyloc nuts.
Step 2. The front of each Ladder pivot is bolted into a
threaded insert molded into the raft using two 3/8" x 1" bolts,
two 3/8" washers and two 3/8" lock washers on top.
Hole
Location
Failure to follow instructions may result in personal injury and may invalidate the
applicable warranty.

Shoremaster 1007970 Specifications

General

Brand	Shoremaster
Model	1007970
Category	Lighting Equipment
Language	English

Summary

Attach Ladder Assembly

Secure Rear Ladder Pivot

Bolt rear ladder pivot through raft hole using 3/8" x 6-1/2" bolts, washers, and secure with brace, washers, and nuts.

Fasten Front Ladder Pivot

Bolt front ladder pivot into raft insert using 3/8" x 1" bolts, washers, and lock washers on top.

Attach Anchor Ring System

Prepare Raft for Anchor Rope

Thread one end of 15' rope through raft cone, secure with knots, and thread through rubber cone.

Connect Anchor Ring

Thread the Anchor Ring onto the 15' rope after securing the raft end.

Attach Second Rope End

Attach the loose end of the rope to the other side of the raft using the same method as the first end.

Final Anchor Rope Connection

Attach the purchaser-provided anchor rope to the Anchor Ring. Use rope, not chain.