SHU
Wearing the Earphones
The
following are
some
suggested
ways
of
wearing
the earphones.
Inserting the Earphones
Insert the earphones so they form a tight seal. The fit
of
the earphone can greatly affect
sound
quality.
Important: If there
seems
to
be
a
lack
of
low
frequency response (bass), this
means
that
the
earphone sleeve is not forming a tight
seal. Gently
push the earphone
deeper
into the
ear
canal
or
try a
different sleeve.
Warning: Do not push
the
earphone sleeve beyond
the
ear
canal opening.
Removing the Earphones
Grasp
the
body
of
earphone
and gently twist to
remove.
Note: Do not pull on cable to remove earphone.
©2013 Shure Incorporated
27A22882 (Rev.
1)
®
SE112
Sound Isolating™
Earphones
Changing Sleeves
Twist
and pull to
remove
the sleeve from the
nozzle.
Slide on a
new
sleeve so that it completely covers
the barb and the nozzle.
Caution: If the barb
or
any
of
the nozzle is exposed,
the sleeve is not properly
installed. Replace sleeves if
they
do
not tightly
grip
the nozzle.
To
ensure
proper fit
and performance,
use
only
sleeves supplied
by
Shure
(unless using custom
molded
sleeves).
Choosing a Sleeve
Soft flex sleeves are included in small, medium, and
large sizes.
Select an earphone sleeve
that
provides
the
best
fit and sound isolation. It should
be
easy
to
insert, fit comfortably,
and
easy to remove.
Soft Flex Sleeves
Using the Remote (m+ models
only)
Use the remote to control compatible
media
phone
players.
~
Play music
Click
the
center
button once
Pause music
Click the
center
button
once.
Change
volume
Click the
volume
up
( +)
or
volume
down
(-) button to
increase
or
decrease
the
volume.
Go
to next track Double-click the
center
button.
Go
to previous
Triple-click
the
center
track
button.
Restart current Triple-click after 6 seconds.
track
Fast-forward
Double-click and hold the
center
button.
Send/End
Call
Click the
center
button
once.
For more information
about
compatible
models
go
to:
www.shure.com
Cleaning the Nozzle
If you notice a
change
in sound quality, remove the
sleeve and
check
the nozzle
of
your
earphone. If
nozzle is blocked,
clear
obstruction
by
using wire
loop end
of
cleaning tool.
Nozzle
Cleaning Tool
Warning:
The
cleaning tool is only to
be
used
to
clean the earphones.
Any
other
use, such
as
using
the tool to clean ears, could result in injury.
Maintenance
and
Cleaning
Careful maintenance ensures a tight seal
between
the sleeve and nozzle, improving
sound
quality and
product safety.
Keep
the earphones
and
sleeves as clean and
dry
as possible.
To
clean sleeves, remove
them
from
earphones, gently rinse in
warm
water
and
air
dry. Foam sleeves require a
longer
drying time.
Inspect for
damage
and
replace if necessary.
Ear
sleeves
must
be
completely
dry
before
reusing.
Wipe the earphones and sleeves with mild
antiseptic to avoid infections. Do not use
alcohol-based disinfectants.
Do not expose earphones to
extreme
temperatures.
Replace sleeves if they
do
not fit properly.
Do not attempt to modify this product. Doing
so
will void the warranty and could result in
personal injury and/or product failure.
Accessories
For information
about
earphone
accessories
and
other
Shure
products visit:
www.shure.com
Furnished accessories subject to change.
Certifications
This product meets the Essential Requirements
of
all relevant European directives
and
is eligible for
CE marking.
The
CE
Declaration
of
Conformity can
be
obtained
from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe
GmbH
Headquarters Europe, Middle East & Africa
Department:
EMEA
Approval
Jakob-Dieffenbacher-Str.
12
75031 Eppingen,
Germany
Phone: 49-7262-92
49
0
Fax: 49-7262-92
49
11
4
Email: EMEAsupport@shure.de
fa
!
~ri~d
in
China
To Next Page
Need help?
General
