Need help?Do you have a question about the Siare Siaretron 4000 and is the answer not in the manual?
Provides thanks for purchase and requests comments on manual usefulness.
Explains the meaning of symbols used to highlight important information in the manual.
Details safety considerations, special requirements, and general safety regulations for the ventilator.
Describes the Siaretron 4000 system's ventilation capabilities and patient types.
Details the ventilator's main blocks, components, and software upgrade possibilities.
Outlines essential checks for proper ventilator connection and function before use.
Introduces the service procedures and chapters covering ventilator maintenance and repair.
Presents a general overview of the Siaretron 4000 ventilator, including available models.
Identifies and labels components and connections visible on the front of the ventilator.
Details electrical interfaces, power supply connections, fuses, and optional ports.
Describes oxygen inlet connections and specifies low and high-pressure requirements.
Explains the ventilator's graphical user interface, its layout, and functionalities.
Describes the functions of the control keyboard, soft keys, and the multifunction encoder knob.
Identifies rear-facing connections, ports, and power supply components.
Explains the information presented on the device's identification label and its symbols.
Introduces maintenance procedures, necessary equipment, and associated hazards.
Outlines the topics covered in the maintenance and service procedures section.
Details routine daily checks and cleaning procedures for the cooling fan filter.
Describes weekly maintenance for turbine air filters, including O-ring and filter replacement.
Lists necessary equipment and components for six-month or 1000-hour maintenance.
Details the annual maintenance procedure for the O2 sensor replacement.
Introduces procedures for internal access and component replacement.
Provides step-by-step instructions for safely replacing the internal batteries.
Details the procedure for removing and replacing the ventilator's turbine module.
Lists the required programmer, cables, and PC software for board programming.
Provides a detailed step-by-step guide for programming the Siaretron 4000 CPU board.
Explains how to set the programming code for specific microcontroller devices.
Lists essential equipment, including simulators and analyzers, for ventilator testing.
Outlines initial setup steps, connections, and simulator parameter configuration.
Details various tests including aesthetics, software version, self-test, and sensor checks.
A table format for recording the results of performed checks and tests.
Lists essential equipment, including simulators and analyzers, for ventilator calibration.
Describes how to navigate the menu to select and initiate calibration routines.
Details the process and conditions for calibrating the turbine's performance characteristics.
Explains the procedure and necessity for calibrating the expiratory flow sensors.
Outlines the steps for calibrating the Positive End-Expiratory Pressure (PEEP) setting.
Describes the procedure to reset the partial operating hours counter for the ventilator.
Discusses calibration adjustments on internal boards, specifically the CPU board.
Provides crucial notes regarding maintenance operations, safety, and component disposal.
Details methods for cleaning, disinfecting, and sterilizing components to ensure safety.
Explains the procedure for chemically disinfecting dismantled parts by immersion.
Summarizes cleaning, disinfection, and sterilization procedures for various ventilator components.
Outlines the schedule and procedures for routine preventive maintenance tasks and operations.
Emphasizes the use of original SIARE spare parts for repairs and maintenance.
Provides guidelines for the proper disposal of batteries, electronic parts, and other components.
Presents a high-level block diagram showing the interconnected electronic boards of the ventilator.
Illustrates the wiring and connections between various components and supply sources.
Lists and briefly describes the role and logic of the main electronic boards.
Details the CPU board, its connectors, and associated functions.
Shows the layout and flow of the pneumatic system for gas delivery and control.
Explains the function of each component within the pneumatic system diagram.
Lists all specific equipment, tools, and instruments required for maintenance and service.
Refers to the User Manual for the technical data sheet of Siaretron 4000 (code 960402).
Provides a table of standard color codes for various medical gases by region.
Defines technical terms, abbreviations, and units of measurement used throughout the manual.
A table format for recording the results of performed checks and tests.
General| Brand | Siare |
|---|---|
| Model | Siaretron 4000 |
| Category | Medical Equipment |
| Language | English |
To Next Page
