preferably lubricated (only with silicon grease) before
repositioning it (Fig. 3).
• Remove the sponges and wash them under running
water.
• Remove the grille on the bottom of the lter and rinse
it out under running water
(Mod. 25 - 40 only)
.
• Wash bio-balls only once a year so to allow the
biological ltration not to be interrupted
(Mod. 25 - 40
only)
.
• Then reassemble the lter following the above
procedures in reverse order.
• PLEASE, OIL PERIODICALLY THE METAL RODS
WITH THE OIL INCLUDED SO TO AVOID FRICTION
OR BREAKING OF THE SAME.
Winter season - The lter must be protected from
frost. During the winter season the lter should should
be switched off, emptied of all water, removed from
the garden and stored in a dry, sheltered place. It is
recommended to leave the lter open during storage.
UV-C lamp replacement
CAUTION: The replacement of the UV-C lamp has to
be done only by specialized personnel staff.
INSTRUCTIONS FOR THE CORRECT DISCHARGE
OF THE PRODUCT ACCORDING TO EU DIRECTI-
VE 2002/96/EC
When used or broken, the product does not have to be
discharged with the other waste. It can be delivered
to the specic electric waste collection centres or to
dealers who give this service. Discharge separately an
electric tool avoid negative consequences for the en-
vironment and for the Health and allows to regenerate
the materials so to have a great saving of energy and
resources.
WARRANTY
This product is guaranteed against defects of mate-
rials and workmanship for a period of 3 years from the
date of purchase, except the UV-C lamp and the O-
rings. The warranty certicate must be lled in by the
dealer and must accompany the pump if it is returned
for reparation, along with the cash register receipt or
similar document. The warranty covers the replace-
ment of the defective parts. In case of improper use,
tampering or negligence by the buyer or user, the gua-
rantee is void and expires immediately. The guarantee
is also void in absence of the cash register receipt or
similar document. The expenses for shipping the pro-
duct to and from the factory, or the repair station, have
to be paid by the buyer.
there are no leaks.
2. If everything is working and the water normally ows
through the lter, connect the plug of the UV-C Lamp and
verify that it is on through the light indicator (g. 1/E).
3. The lter can work 24 hours/day for the entire year
except if the temperature drops below 4°C. To avoid
damages, unplug the power and empty completely the
lter.
CONNECTING THE HOSES
The GREEN RESET lter requires three exible tubes
which are not included. One to connect the pump with
the inlet coupling (g. 1/A), another to ush the clean
water from the lter outlet (g. 1/B) back to the pond.
Another to connect the drainpipe (g. 1/C) dirty wa-
ter when sponges cleaning is done. This water can be
used as fertilizer. When installing Green Reset lter, it
is important that the exible hoses diameters are cor-
rectly sized. This will allow the pump to obtain maxi-
mum water ow performances. Always fasten the ho-
ses to the couplings with metal clamps (not included).
CLEANING OF THE SPONGES WITH THE SELF
CLEANING SYSTEM
GREEN RESET is equipped with a self-cleaning
system, that allows to clean the sponges without
opening the lter.
Proceed as follows:
• Lift completely the handle on the top of the lter (g.
4).
• Turn both the hand grips from the position “FILTER”
to the position “CLEAN” clockwise or anticlockwise
until the writing CLEAN corresponds to the small hole
in the handle (g. 5).
• Remove the cap (g. 6/A) from the debris outlet,
connect the stepped hose connector (g. 6/B) and
a exible tube (not compulsory). Position the tube
towards the plants/owers you would like to fertilize.
• Turn clockwise, with strength, the ow selector handle
to the “CLEAN” position (g 7).
• Push up and down the top handle (g. 8) to squeeze
the sponges. Repeat this operation until clean water
come out from the lter. When cleaning is completed,
rell the pond as you like.
• To settle the lter for normal operation, lift up
completely the top handle (g. 9/F).
• Turn both the hand grips from “CLEAN” position to
“FILTER” position (g. 10/G).
• Lower completely the top handle (g. 8/F).
• Turn the ow selector handle anticlockwise to the
“FILTER” position (g. 11/F).
• Remove the stepped hose connector (g. 6/L) from the
debris outlet and close it with the original cap (g. 6/I).
If the lter, after cleaning operations, is still blocked,
proceed with the lter maintenance.
FILTER MAINTENANCE
Cleaning and replacement of sponges.
The maintenance of the lter has to be done only if the
self-cleaning system cannot fully clean the sponges
because they are worn out or blocked.
CAUTION: Always disconnect the lter from the power
supply before any maintenance operations.
• Do not open the V-band (g. 1/M) before having
unplugged the pump and UV-C lamp.
• The cap of the UV-C lamp compartment can be
opened only by specialized personnel.
• Open the V-band (g. 1/M).
• Remove the lter dome with special care to do not
damage the OR gasket. This should be washed and
To Next Page
Loading...
