EasyManua.ls Logo

Signature Hardware ACRYLIC ALCOVE TUB User Manual

Signature Hardware ACRYLIC ALCOVE TUB
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
1
1.800.221.3379
ACRYLIC ALCOVE TUB
INSTALLATION INSTRUCTIONS
BAÑERA ESTILO ALCOVE DE ACRÍLICO INSTRUCCIONES DE INSTALACIÓN
REVISED 6/20/2019
BEFORE YOU BEGIN
We recommend consulting a professional if you are
unfamiliar with installing bathroom fixtures and
plumbing. Signature Hardware accepts no liability for
any damage to the floor, walls, plumbing, or personal
injury during installation.
Observe all local plumbing and building codes.
Unpack and inspect the product for shipping
damage. If any damage is found, contact our
Customer Relations team at 1-800-221-3379.
GETTING STARTED
Ensure that you have gathered all of the required
materials that are needed for the installation.
Ensure that your bathroom floor is adequately
supported, and the finished floor is level.
Refer to the product’s specification sheet for all
rough-in dimensions and information. However, it is
highly recommended that all rough-in procedures are
performed with the tub on-site.
Handle the tub by its shell only. Do not lift the tub by its
plumbing at any time.
The variety of installations for this tub may require
framing procedures other than those shown in this
manual.
Keep the plumbing connections around the tub easily
accessible for any future maintenance that may be
necessary.
ANTES DE COMENZAR
Le recomendamos que consulte a un profesional si no
sabe cómo instalar accesorios de baño y no tiene
conocimientos de plomería. Signature Hardware no
asume ninguna responsabilidad con respecto a los daños
causados al piso, muros, tuberías o lesiones personales
durante la instalación.
Cumpla con todas las normas locales de plomería y
construcción.
Retire el producto del empaque y verifique si no sufrió
daños durante el envío. Si encuentra algún daño,
comuníquese con nuestro Equipo de Servicio al Cliente al
1-800-221-3379.
CÓMO COMENZAR
Asegúrese de haber reunido todos los materiales
necesarios para la instalación.
Asegúrese de que el suelo del baño tenga el apoyo
adecuado y que el suelo terminado esté nivelado.
Consulte la hoja de especificaciones del producto para
conocer los detalles y dimensiones de las instalaciones
ocultas. Sin embargo, es altamente recomendable que
todos los procedimientos de las instalaciones ocultas sean
realizados con la bañera en el lugar.
Maneje la bañera únicamente por su casco. No levante la
bañera usando la tubería en ningún momento.
La diversidad de instalaciones para esta bañera podría
requerir procedimientos de encuadre diferentes a los
mostrados en este manual.
Mantenga las conexiones de plomería que están alrededor
de la bañera fácilmente accesibles para los futuros
servicios de mantenimiento que sean necesarios.
Question and Answer IconNeed help?

Do you have a question about the Signature Hardware ACRYLIC ALCOVE TUB and is the answer not in the manual?

Signature Hardware ACRYLIC ALCOVE TUB Specifications

General IconGeneral
BrandSignature Hardware
ModelACRYLIC ALCOVE TUB
CategoryBathtubs
LanguageEnglish

Summary

BEFORE YOU BEGIN

GETTING STARTED

TOOLS AND MATERIALS

FRAMING & INSTALLATION

Integral Drain

Install drain assembly, applying silicone sealant to threads for a watertight seal.

Brass Exposed Pipe Drain

Trim drain and overflow pipes to size, applying sealant to threaded pipe ends.

PVC Cable Drain

Apply solvent cement to PVC connections and sealant to overflow gasket and tub around the hole.

Reference for Correct Tile Flange Installation

CLEANING AND MAINTENANCE

SCRATCH REMOVAL

Clean scratched area with damp sponge, use sandpaper, then polish with acrylic compound.