SignWarehouse.com Bobcat BA-60

Questions and Answers

C
Christina MendozaAug 15, 2025
What to do if my SignWarehouse.com Bobcat BA-60 shows 'Communication error'?
- D
  Debbie PooleAug 15, 2025
  First, verify that the serial, USB, or parallel cable is correctly connected to both the cutting plotter and your computer. Next, ensure that the interface settings are accurate. Confirm that the communication settings on your PC match those on your cutting plotter (e.g., 9600bps, no parity, 8 bits, 1 stop bit). Finally, press the ON/OFF Line key to return to On Line mode.
A
andrew20Aug 18, 2025
What to do if my SignWarehouse.com Bobcat BA-60 doesn't repeat cutting?
- L
  Louis JohnsonAug 18, 2025
  If your cutting plotter fails to repeat a cut, it could be due to the absence of data in the buffer or the buffer being full. To resolve this, resend the job from your computer to the cutting plotter.
M
Melissa WoodsAug 21, 2025
Why is my SignWarehouse.com Bobcat BA-60 graph clipped?
- B
  Brian Johnson MDAug 21, 2025
  Graph clipping occurs when the cutting graph exceeds the available cutting area. To fix this: * Reload a wider or longer media. * Move the pinch rollers to expand the cutting area. * Re-scale the graph to a smaller size and resend the cutting job from your computer.
M
Mary McdanielAug 25, 2025
What to do if my SignWarehouse.com Bobcat BA-60 Cutter displays 'Check media, or Y motor'?
- C
  Christian HillAug 26, 2025
  This message indicates a potential obstruction to the carriage or an issue on the Y-axis. Clear any obstructions, ensuring the carriage moves smoothly. Then, power cycle the cutting plotter by turning it off and back on.
B
Brian WashingtonAug 28, 2025
How to fix 'Check the media, drum or X-motor' error on SignWarehouse.com Bobcat BA-60?
- M
  Mark CervantesAug 28, 2025
  This error suggests a possible issue on the X-axis. Ensure the drums are functioning correctly and the media is properly loaded. Following this, power cycle the cutting plotter.
T
trevordiazAug 31, 2025
What to do if my SignWarehouse.com Bobcat BA-60 cannot operate?
- L
  Laura GonzalezAug 31, 2025
  If the POWER LED is lit, the cutting plotter should be in normal working order. Try turning the cutting plotter off and then on again to see if that resolves the problem. If the POWER LED is not lit, please contact your local dealer.
C
Charles WalkerSep 4, 2025
Why does my SignWarehouse.com Bobcat BA-60 show 'HPGL/2 command error'?
- J
  jefframosSep 4, 2025
  This error means the cutting plotter isn't recognizing commands from your computer. Verify the commands applied to your cutting plotter are in the HP-GL/2 or HPGL format. Then, resend the job to the cutting plotter.
J
jennifercuevasSep 7, 2025
What to do if my SignWarehouse.com Bobcat BA-60 Cutter displays 'Width sensor error'?
- H
  Hailey MosleySep 7, 2025
  Ensure that the pinch rollers are positioned correctly above the grid drum, and then reload the media.
T
Thomas HolderSep 10, 2025
What to do if my SignWarehouse.com Cutter displays 'Lever up or no media'?
- L
  Lori RobbinsSep 10, 2025
  Make sure you have lowered the lever and that you load the media before starting the cutting process.