The F-300DT Digital Facial Steamer is a beauty instrument designed to support other beauty instruments and beautician trolleys. It is available in several models, including F-300D, F-300H, F-300E, F-300F, 3021, 3051, and 3052.
Function Description:
The primary function of the F-300DT is to generate steam for facial treatments. It features an ozone display and spray display, indicating its ability to produce ozone-infused steam. The device allows for adjustment of energy and time settings, with dedicated buttons for increasing and decreasing both. An ozone indicator light and vapor indicator light provide visual cues for the operational status. It also includes an ozone switch and spray switch for controlling these functions. The steamer is designed to convert water into a fine mist, which can be sprayed out with the smell of ozone, indicating normal spray state for beauty operations. For aromatherapy, users can add essence to a dedicated cap on top of the nozzle.
Important Technical Specifications:
- Model Type: F-300DT
- Frequency: 50/60Hz
- Wattage: 650W/800W
- Voltage: AC 100-120V or AC 220-240V
Usage Features:
The F-300DT offers two methods for adding water.
- Method One: Unscrew the funnel cap, press and hold a gray button on the host to remove the water cup, add water, and then reinsert the water cup into the bayonet pit, ensuring it is installed in place.
- Method Two: Remove the funnel cap and add water directly, ensuring the funnel cap and funnel filter mesh are tightened afterward.
- Water Level: It is crucial to ensure the water in the water cup is between the safe water level (MIN-MAX).
- Initial Use: For the first use, it is recommended to use tap water to avoid scale generation, then switch to pure water. If the detection function responds incorrectly due to overly pure water, working with tap water once can resolve it.
- Operation: After connecting power, the device enters standby. Users can adjust time and energy. For faster heating, especially with room temperature water, energy should be set to maximum. Once water boils, pressing the ozone switch activates the ozone indicator light, and steam is produced.
- Aromatherapy: To use aromatherapy, open the essence cap on the nozzle, add 2 drops of essence, and close the cap.
- Safety Precautions:
- Do not move, tilt, shake, or move the product during operation to prevent hot water splashes or excessive steam ejection.
- Avoid touching high-temperature parts like nozzles and funnel caps during operation.
- Do not start if the water level is below the lowest mark.
- Do not use the product under direct sunlight for extended periods.
- Do not disassemble the device without permission.
- If the water level is too low, the host will beep and stop spraying, requiring water addition and restart.
- Use purified or tap water; avoid distilled water or viscous substances like flavors or herbal extracts, as these can cause damage and water spray issues.
- Ozone has bactericidal effects, but prolonged use can damage skin and herbal nutrition. Adjust usage time based on skin type.
- Do not spray directly on the skin immediately; wait until a stable, fine mist is produced.
- Maintain a specific distance during spraying: 35-40cm for oily/poor circulation skin and normal skin (15min duration), 40-45cm for sensitive/dry skin (5min duration), and 40cm for inflamed skin (5min duration).
- If water leakage occurs, check the seal ring and reinstall the water cup.
- Keep the device away from high-interferential devices. If interference occurs, turn off, wait 15 seconds, and restart.
- Ensure the funnel cap is tightened correctly to prevent steam leakage, but avoid overtightening to prevent premature aging of the sealing ring.
Maintenance Features:
- Post-Operation Cleaning: Clean the product promptly after each use.
- Water Cup and Heating Plate: Clean scale from the water cup and heating plate at least once a week or after two uses of the funnel. This can be done by scrubbing with a soft metal brush or soaking in vinegar for 5-7 minutes, then rinsing with tap water. The funnel itself cannot be reused.
- Seal Ring: Check the seal ring every 2 weeks and replace it if deformed or deteriorated. Each product comes with a spare seal ring, and replacements can be obtained from the dealer if lost or damaged.
- Funnel Filter Mesh: Always add water with the funnel filter mesh in place to prevent water from flowing to other parts and causing a short circuit.
- Troubleshooting: In case of abnormal operation (e.g., sprayer not working, product heating up before spray function), immediately cut off power and contact the dealer or maintenance center. Solutions for common issues include checking power connection, adjusting energy settings, ensuring sufficient water, and cleaning clogged nozzles.
The device is designed for easy assembly, with components such as a five-leg base, five-wheel legs, straight post, pressing plate, flat gasket, spring shim, screws, wrench, accessories, sliding bar, steamer holder, cross screws, board, and the facial steamer unit itself. Detailed diagrams illustrate the assembly process for the base, main body, and steamer head.
The F-300DT is a versatile and user-friendly facial steamer, provided that all safety and maintenance guidelines are followed carefully.
Need help?
General
To Next Page