Use the external adjustments with respect of position 1 & 2 of the adjustment
points (26 & 28) and button position (25). (Fig. G).
The horizontal adjustment is made through: Point 1 (28) = lamp 1
Point 2 (26) = lamp 2
The vertical adjustment is made through central point (27) (common for both
lamps). (See fig.G “OK”).
Adjustment of the lamp must be made when you place a new lamp and also
after carriage of the projector.
If you cannot get the right adjustment, make sure the lamp is correctly driven
in its socket.
IMPORTANT: When changing the lamps, make sure than the projector is cool.
Firstly, adjust Lamp 2, then Lamp 1.
Note: On projector with one lamp model, only height adjustment is possible.
A7 - SETTING OF THE LAMPS AND CONDENSER LENS
Important ! Make sure the projector is cool enough to gain safe access to
the lamps and condenser.
Disconnect the projector from the mains.
Take off the side door (5) (see Fig. H), using a coin.
If you change the lamp, you must put new lamp with same power and voltage
characteristics of the original one.
A7-1 - Setting of the lamps
See § A6.1
Set the lamp holder lever (button 25) to “L2” position.
Pull out the lever and slide it towards the door side of the projector.
Using the lamp holder lever, flick towards the exterior (fig. I).
Fit the new lamp without touching it with bare fingers.
Flick the lamp holder back into place.
Raise the lamp holder lever, pull it backwards and push to Lamp 2 position.
Set the projector in Lamp 1 position.
Replace the side door
Adjust the lamp (see chap. A6.3)
Note: On one lamp model you just have, using the lamp holder lever, flick
towards the exterior.
Models 3245 AF & 3445 AF
After the replacement of the lamp and the start-up of the projector, it
is necessary to “delete” the “L2” signal.
To do so, press simultaneously the buttons 21 & 22 for 3 to 4 seconds
(The signal will blink until extinguished)
.
A7-2 - Setting of the condenser lens
(See chap. A2-6 and A2-7)
Condenser can be adapted to the slide size and to the lens. This ensures
better distribution of light on the screen.
Set the single lens “PC” in 4x4 position if necessary (fig. J)
Replace it by model “FL” useful for large focus length lens (from 150/180mm)
Condensor lens is adapted on removable supports. They are locked in position
with a spring. Lift spring to remove the condensor lens support.
A8 - SLIDE CHANGING IN AUTOMATIC CYCLE
“TIMER” and “AUTOSHOW” modes allow to automatic projection and
continuous projection of a series of slides.
Projection time can be chosen between 2 and 120 seconds in one second
intervals.
Put the switch (15) in “IN” position.
Important: the programming is made when projector is on and it is stored in a
memory until reprogrammed.
A8-1 - Programming of the projection time
Press on button 21 (“Auto timer”) waiting for the LED on the right to flash.
Continue pressing on this button to obtain the interval time you want for your
projection (one flash = one second).
A8-2 - “TIMER” function
This mode is used when you have 80 slides.
Program the time projection (Chap. A8-1)
Slide tray goes forward slide by slide continuously with a non-stop at the zero
position.
To program the timer mode, press on touch 21 and then on touch 13 (reverse)
before the LED flashing, then release both.
A quick pressure on touch 21 allow to stop (LED off) or to play (LED on) this
mode.
It is possible to put a slide in the zero position.
It is possible to stop the timer cycle using the wired remote control (CAD)
connected on DIN 6 pins plug (17), to see the previous slides. A reverse
command disable the timer function and LED (21) twinkles. Other reverse
commands allow reverse actions. A forward command enable timer function.
Note: Actions on button 12 and 13 (or Forward / reverse button) of a remote
control wil be executed. Then the cycle continues.
A8-3 - “AUTOSHOW” function
This mode allows to show continuously a series of slides (1 to 78).
Program the time projection (chap. A8-1)
The first slide is always the slide N°1.
Slide tray goes forward slide by slide. A break of two empty slide slots will
initiate a rapid homing and cycle will start again.
To program AUTOSHOW mode, press on button 21 (Autotimer) and then on
button 12 (forward) before the LED flashing, then release both.
A quick pressure on button 21 allows to stop (LED off) or play (LED on) this
mode.
Note: Actions on button 12 or 13 (or Forward/reverse button) of a remote
control will be executed. Then the cycle continues.
To Next Page
Loading...
