SIMONSWERK Anselmi AN 140 3D ALU

To Next Page

Opzionale Optional

Avvitare la vite aggiuntiva D. 3,5 mm

per bloccaggio verticale fino al fermo

ed estrarre il cuneo di regolazione.

Screw in the optional screw D. 3.5 mm

for vertical fixing up to the stopper

and pull the adjustment wedge.

Spingere il cuneo sotto la porta sino a

raggiungere la luce da terra desiderata;

bloccare nuovamente le viti.

Slide the wedge under the door until

achieve the desired measure

from the ground; re-lock the screws.

Inserire cuneo di regolazione sotto la

porta e svitare di un giro le viti di

fissaggio della cerniera sulla porta;

la porta si appoggia sul cuneo.

Insert the adjustment wedge under the

door and unscrew one turn the fixing

screws of the hinge on the door;

the door rests on the wedge.

Regolazione Altezza Height Adjustment

D Vite autobloccante

per regolazione laterale.

Self-locking screw for

lateral adjustment.

E Eccentrico per

regolazione profondità.

Excentric system for

depth adjustment.

F Vite opzionale D.3,5 mm per

fissaggio verticale porta.

Optional D.3,5 mm screw for

vertical fixing of the door.

A Foro viti di fissaggio

della cerniera allo stipite.

Fixing hole for the hinge

to the frame.

B Fori asolati per

regolazione verticale

e fissaggio alla porta.

Oval holes for vertical

adjustment and fixing

to the door.

C Vite di fissaggio

regolazione profondità.

Fixing screw of

depth adjustment.

ISTRUZIONI REGOLAZIONE Adjustment Instructions

Porta DoorStipite Frame

FRESATURE MILLING

AN 140 3D ALU / AN 160 3D ALU DIT_SP_024 Rev.01 18/04/2018

Anselmi & C. srl

31056 Roncade (Treviso)

via Ca’ Morelli 19

tel. +39 0422 707 426

fax +39 0422 840 836

www.anselmisrl.it

13 2424

25,5

110

12 12

424 4,5

12 12

110

4 24

2727

Min. 1,5 - Max 4,5

110

13 24

Ø 5

105

Need help?

Do you have a question about the SIMONSWERK Anselmi AN 140 3D ALU and is the answer not in the manual?

Overview

Function Description
Important Technical Specifications
Dimensions and Milling
Adjustment Ranges
Usage Features
Installation Preparation
Adjustment Procedures
Height Adjustment (Regolazione Altezza)
Depth Adjustment (Regolazione Profondità)
Lateral Adjustment (Regolazione Laterale)
Maintenance Features

This document describes the Anselmi AN 140 3D ALU / AN 160 3D ALU concealed hinge, a product from Anselmi & C. srl, a member of SIMONSWERK. This hinge is designed for doors and offers advanced adjustability in three dimensions: depth, lateral, and height.

Function Description:

The Anselmi AN 140 3D ALU / AN 160 3D ALU is a concealed hinge system that allows for precise alignment of doors within their frames. Its primary function is to provide a robust and aesthetically pleasing connection between the door and the frame, while offering comprehensive adjustability to compensate for installation inaccuracies or to fine-tune door positioning. The "3D" in its name signifies its ability to be adjusted in three axes, making it highly versatile for various door types and installation scenarios. The hinge is designed to be fully concealed when the door is closed, contributing to a clean and modern aesthetic.

Important Technical Specifications:

Dimensions and Milling:

The hinge requires specific milling dimensions for both the frame (stipite) and the door (porta).

Frame Milling (FRESATURE MILLING - Stipite Frame):
- Overall height: 110 mm
- Width: 24 mm
- Depth: 27 mm (minimum 1.5 mm, maximum 4.5 mm)
- The milling for the frame includes a central section of 24 mm width and two outer sections of 13 mm each, totaling 50 mm in width.
- The depth of the milling for the frame is 27 mm.
- There are also specific milling requirements for the screw holes, with a diameter of 12 mm for the main fixing screws.
Door Milling (FRESATURE MILLING - Porta Door):
- Overall height: 110 mm
- Width: 24 mm
- Depth: 27 mm (minimum 1.5 mm, maximum 4.5 mm)
- Similar to the frame, the door milling also has a central section of 24 mm width and two outer sections of 13 mm each, totaling 50 mm in width.
- The depth of the milling for the door is 27 mm.
- The screw holes for the door have a diameter of 12 mm.
Hinge Dimensions (Overall):
- Total height: 110 mm
- Total width (when closed): 24 mm
- Total width (when open, including the hinge mechanism): Approximately 100 mm (from the diagram)
- The hinge body itself measures 110 mm in height and 24 mm in width.
- The fixing plates extend beyond this, requiring the wider milling dimensions.

Adjustment Ranges:

Depth Adjustment (Regolazione Profondità):
- The hinge allows for a depth adjustment of ±1 mm. This is achieved by manipulating the eccentric (E) and fixing screws (C).
Lateral Adjustment (Regolazione Laterale):
- The hinge offers a lateral adjustment of ±1.5 mm. This is performed by turning the self-locking screw (D).
Height Adjustment (Regolazione Altezza):
- The height adjustment range is not explicitly stated with a numerical value but is described as allowing the door to be raised or lowered to achieve the desired measure from the ground. This adjustment is performed by using a wedge and loosening/tightening the hinge fixing screws on the door.

Usage Features:

Installation Preparation:

A - Fixing hole for the hinge to the frame: This refers to the primary screw holes used to secure the hinge to the door frame.
B - Oval holes for vertical adjustment and fixing to the door: These oval-shaped holes on the door side of the hinge allow for initial vertical positioning and subsequent fixing.
C - Fixing screw of depth adjustment: This screw, along with the eccentric, controls the depth of the door relative to the frame.
D - Self-locking screw for lateral adjustment: This screw is used to adjust the door's position horizontally.
E - Excentric system for depth adjustment: This eccentric mechanism works in conjunction with screw C to fine-tune the door's depth.
F - Optional D.3,5 mm screw for vertical fixing of the door: An additional screw that can be used for more secure vertical fixing after height adjustment.

Adjustment Procedures:

Height Adjustment (Regolazione Altezza):

Step 1: Insert an adjustment wedge under the door. Unscrew the hinge fixing screws on the door by one turn. The door will then rest on the wedge.
Step 2: Slide the wedge further under the door until the desired gap from the floor is achieved. Re-lock the screws.
Optional: For additional vertical locking, screw in the optional D.3.5 mm screw until it stops, then remove the adjustment wedge. This provides a more permanent vertical fix.

Depth Adjustment (Regolazione Profondità):

Step 1: Unscrew the C screws by one turn.
Step 2 (Clockwise): Acting on the eccentric E in a clockwise direction moves the door inwards by -1 mm (towards the frame).
Step 2 (Counter-clockwise): Acting on the eccentric E in a counter-clockwise direction moves the door outwards by +1 mm (away from the frame).
Step 3: Once the desired depth is achieved, fix both C screws.

Lateral Adjustment (Regolazione Laterale):

Step 1: Act on the D screw.
Step 2 (Clockwise): Acting on the D screw in a clockwise direction moves the door laterally by -1.5 mm (e.g., closer to the hinge side of the frame).
Step 2 (Counter-clockwise): Acting on the D screw in a counter-clockwise direction moves the door laterally by +1.5 mm (e.g., further from the hinge side of the frame).

Maintenance Features:

The document does not explicitly detail specific maintenance features such as lubrication schedules or part replacement. However, the design with accessible adjustment screws implies that fine-tuning and re-adjustment can be performed as needed over the lifespan of the door and hinge. The robust construction and the ability to precisely adjust the door's position contribute to the longevity of the door system by preventing undue stress on the hinges or frame due to misalignment. The optional D.3.5 mm screw for vertical fixing suggests a method to enhance stability and potentially reduce the need for frequent height adjustments once the door is optimally positioned.