Sinope Sedna VA4220WF

To Next Page

Download the free Neviweb app on your

device from the AppStore or Google Play*. Connect the valve to an

electrical outlet, using

the supplied adapter,

near where it will be

installed. By doing so,

you will validate the

range of the Wi-Fi

communication

between the valve

and your network.

Open the app and log into your

Neviweb account or create an

account.

Follow the steps to add a

device.

Connect your Sinopé

smart water leak

detectors (Step 2).

Remove the valve

cover by unscrewing

the 4 screws with a flat

screwdriver.

The mode switch of the

valve must be in

position "1".

The valve must be

plugged into a

power outlet.

Connect the detector

to the network from its

installation location.

This will ensure it is

within range of the RF

signal of the valve.

Remove the cover and

insert the batteries.

Once all the detectors

are connected, press

the "B" button on the

valve to close the

connectivity session.

Press the "B" button to

open the network

connectivity session for

the detectors.

The indicator lights will

light up in sequence to

indicate that the session

is active.

VA4220WF

VA4221WF

Installation Guide

Smart Water Valve

Wi-Fi

*It is also possible to operate the valve without an Internet connection.

However, you will not be notified when a water leak is detected.

Refer to the "Support" section of our Website at www.sinopetech.com.

The connection can be verified at

any time by pressing the water leak

detector's button. The indicator light

will light up in green for 10 seconds

if the unit is connected.

WARNINGS AVAILABLE ACCESSORIES

The installation of this valve should be performed by a certified

professional in conformity with local and national construction codes.

The valve closes with sufficient force to cut a finger. ALWAYS keep

your fingers away from the ball valve.

Although each unit is pre-tested at the factory, it is strongly

recommended that you test the valve before installation to

ensure proper operation in your home.

STEP 1

CONNECTING THE VALVE TO YOUR WI-FI NETWORK

STEP 2

CONNECTING THE WATER LEAK DETECTORS TO THE SMART WATER VALVE

*Refer to the "Support" section of our Website at www.sinopetech.com.

Press the detector's connection button.

Green light blinks

Green light lit for 10 s

Red light turns on

Device is connecting

Successful connection

Connection has failed*

StatusLight

Flow Sensor

FS4220

On-Off switch

SW2500ZB

Load Controller

RM3250ZB

Smart Plug

SP2600ZB

Smart Outlet

SP2610ZB

Multicontroller

MC3100ZB

Need help?

Do you have a question about the Sinope Sedna VA4220WF and is the answer not in the manual?

Summary

Connecting the Valve to Your Wi-Fi Network

Download and Install Neviweb App

Get the Neviweb app from the App Store or Google Play for device setup.

Prepare Valve for Connection

Remove the valve cover by unscrewing four screws to access internal components.

Connect Valve to Power and Network

Plug the valve into an electrical outlet and validate Wi-Fi communication range.

Add Valve to Neviweb Account

Open the Neviweb app, log in, and follow the steps to add the smart water valve.

Connecting Water Leak Detectors to the Smart Water Valve

Prepare Valve and Detectors

Ensure the valve mode switch is on '1' and plug it into a power outlet.

Initiate Detector Pairing

Press the 'B' button on the valve to start the network connectivity session for detectors.

Connect Detectors to Network

Connect detectors from their installation location to ensure RF signal range and insert batteries.

Finalize Connectivity Session

Press the 'B' button on the valve to close the session and verify detector connection.

Installation of Smart Water Leak Detectors

Detector Placement Guidelines

Position detectors where potential water leaks may occur, such as near water heaters or sinks.

Connect Sensor and Attach Detector

Connect the sensor to the detector and attach the detector to a clean surface using provided hardware.

Test Water Leak Detector

Test the detector by touching electrodes with water to activate the audible alarm.

Installation of the Smart Water Valve

Prepare Valve for Installation

Ensure valve is OPEN, separate controller, close main water supply, and remove safety caps.

Install Smart Water Valve

Install the valve downstream of the main shut-off valve, potentially requiring additional fittings.

Secure Valve Controller

Replace the controller onto the valve and secure it with the pin, ensuring OPEN position.

Restore Water Supply and Power

Power the valve with the adapter, insert optional batteries, and open the main water supply.