EasyManua.ls Logo

SJE Rhombus Tank Alert User Manual

SJE Rhombus Tank Alert
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Some states do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. Some states do
not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
TO OBTAIN WARRANTY SERVICE: The consumer shall assume all
responsibility and expense for removal, reinstallation, and freight. Any
item to be repaired or replaced under this warranty must be returned
to SJE-RHOMBUS
®
, or such place as designated by SJE-RHOMBUS
®
.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS ARE
LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. SJE-RHOM-
BUS
®
SHALL NOT, IN ANY MANNER, BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES AS A RESULT OF A BREACH OF
THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY.
The Tank Alert
®
ABP indoor alarm panel provides a reliable means of controlling a 120 VAC single phase pump in water and
wastewater installations. Two switches, one for the pump and one for the high water alarm, are spliced together for easy installation.
The Tank Alert
®
ABP alarm panel horn sounds when a potentially threatening liquid level condition occurs. The horn can be turned
off, but the alarm light remains on until the condition is remedied. Once the condition is cleared the alarm panel will automatically
reset. A green "Power On/Pump Run" light indicates 120 VAC primary power to the alarm, and also flashes to indicate the pump
run status. Low battery chirp feature indicates when battery should be replaced.
TANK ALERT
®
ABP alarm panel Installation Instructions
TANK ALERT
®
ABP ALARM PANEL
SJE-RHOMBUS
®
THREE-YEAR LIMITED WARRANTY
Q
120 VAC Model Voltage - (circuits not supervised) Primary: 120 VAC, 60 Hz, 2.4 watts maximum
Operating Voltage: 9 VDC
Q
NEMA 1 enclosure rated for indoor use.
Q
Automatic alarm reset.
Q
Red "alarm" light and green "power on/pump run" light, alarm "test" switch, and horn "silence"
switch.
Q
6 foot (1.8 meter) power cord
Q
Alarm horn sounds at 87 decibels at 10 feet (3 meters).
Q
Manual pump run operation.
Q
If primary power fails, the alarm panel continues to work due to battery backup feature.
Battery Backup Power - (circuit not supervised) 9 VDC
Q
Complete package includes two factory-spliced SJE MilliAmpMaster
control switches with 10
feet (3.05 meters) of cable and mounting clamp.
Q
Switching mechanism operates on low voltage and is isolated from the power line to reduce the
possibility of shock.
Q
Receptacle on bottom to plug in pump power cord.
Q
Low battery chirp.
Q
External terminal block for easy float switch installation.
Q
Three-year limited warranty.
SJE-RHOMBUS
®
warrants to the original consumer that this product
shall be free of manufacturing defects for three years after the date of
consumer purchase. During that time period and subject to the condi-
tions set forth below, SJE-RHOMBUS
®
will repair or replace, for the
original consumer, any component which proves to be defective due to
defective materials or workmanship of SJE-RHOMBUS
®
.
ELECTRICAL WIRING AND SERVICING OF THIS PRODUCT MUST
BE PERFORMED BY A LICENSED ELECTRICIAN.
THIS WARRANTY DOES NOT APPLY: (A) to damage due to lightning or
conditions beyond the control of SJE-RHOMBUS
®
; (B) to defects or
malfunctions resulting from failure to properly install, operate or main-
tain the unit in accordance with printed instructions provided; (C) to
failures resulting from abuse, misuse, accident, or negligence; (D) to
units which are not installed in accordance with applicable local codes,
ordinances, or accepted trade practices, and (E) to units repaired and/
or modified without prior authorization from SJE-RHOMBUS
®
.
PREVENTATIVE MAINTENANCE
Periodically inspect the product. Check that the cable has not become worn or that the housing has not been damaged so as to impair the protection of the
product. Replace the product immediately if any damage is found or suspected.
Periodically check to see that the floats are free to move and operate the switches.
Use only SJE-Rhombus
®
replacement parts.
For indoor use only.
Pump must have integral thermal overload protection.
Patent Pending
INSTALL INSTRUCTIONS
109
Question and Answer IconNeed help?

Do you have a question about the SJE Rhombus Tank Alert and is the answer not in the manual?

SJE Rhombus Tank Alert Specifications

General IconGeneral
BrandSJE Rhombus
ModelTank Alert
CategorySecurity System
LanguageEnglish

Summary

Preventative Maintenance

Product Inspection and Care

Regularly check product for worn cables or damaged housing. Replace if any damage is found.

Float Switch Operation

Periodically check that float switches are free to move and operate correctly.

Use of Genuine Parts

Only use SJE-Rhombus® replacement parts for maintenance and service.

Application Environment

Ensure the product is used only for indoor applications as specified.

Pump Thermal Overload

Verify that the pump is equipped with integral thermal overload protection.

SJE-Rhombus Three-Year Limited Warranty

Warranty Coverage Details

Covers defects in materials or workmanship for three years from consumer purchase date.

Warranty Exclusions

Excludes damage from lightning, improper installation, abuse, or unauthorized modifications.

Obtaining Warranty Service

Consumers are responsible for removal, reinstallation, and freight for warranty service.

Limitation of Liability

Limits liability for incidental/consequential damages and duration of implied warranties.

Safety Warnings

Electrical Shock Hazard Warning

Disconnect power before installation/servicing. Must be installed by a qualified person.

Explosion or Fire Hazard Warning

Do not use with flammable liquids or in hazardous locations as defined by NEC.

Installation Instructions

Panel Mounting and Location

Determine indoor location, insert screw, and hang alarm panel using keyhole.

Float Switch Installation

Place float switch cords into clamps, secure floats at desired levels, tighten hose clamps.

Wiring and Power-Up

Connect cable leads, install battery, plug into GFI-protected receptacle.

System Testing Procedure

Manually tip floats to test horn and pump activation. Test weekly.

Battery Maintenance

Replace battery every 12 months or after alarm. Listen for low battery chirp.

Cable Management

Secure pump power cord using cable clasp and bundle cables with tie strap.

Related product manuals