d Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool
Power tools are dangerous in the hands of
untrained users
e Maintain power tools Check for misalignment or
binding of moving parts breakage of parts and any
other condition that may affect the power tools
operation If damaged have the power tool repaired
before use Many accidents are caused by poorly
maintained power tools
f Keep cutting tools sharp and clean Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control
g Use the power tool accessories and tool bits etc in
accordance with these instructions taking into
account the working conditions and the work to be
performed Use of the power tool for operations dierent
from those intended could result in a hazardous situation
BATTERY TOOL USE AND CARE
a Recharge only with the charger specified by the
manufacturer A charger that is suitable for one type of
battery pack may create a risk of re when used with
another battery pack
b Use power tools only with specifically designated
battery packs Use of any other battery packs may
create a risk of injury and re
c When battery pack is not in use keep it away from
other metal objects like paper clips coins keys
nails screws or other small metal objects that can
make a connection from one terminal to another
Shorting the battery terminals together may cause burns
or a re
d Under abusive conditions liquid may be ejected
from the battery avoid contact If contact
accidentally occurs flush with water If liquid
contacts eyes additionally seek medical help Liquid
ejected from the battery may cause irritation or burns
SERVICE
a Have your power tool serviced by a qualified repair
person using only identical replacement parts This
will ensure that the safety of the power tool is maintained
SAFETY INSTRUCTIONS FOR CORDLESS
DRILLDRIVERS
Avoid damage that can be caused by screws nails and
other elements in your workpiece remove them before
you start working
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger
In case of electrical or mechanical malfunction
immediately switch o the tool or unplug charger from
power source
SKIL can assure awless functioning of the tool only
when original accessories are used
Use only accessories with an allowable speed matching
at least the highest noload speed of the tool
The toolcharger is not intended for use by persons
including children with reduced physical sensory or
mental capabilities or lack of experience and knowledge
unless they have been given supervision or instruction
concerning use of the toolcharger by a person
responsible for their safety
Ensure that children do not play with the toolcharger
Secure the workpiece a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory or fastener may contact hidden wiring or
its own cord cutting accessory and fasteners
contacting a live wire may make exposed metal parts of
the power tool live and could give the operator an
electric shock
Use suitable detectors to find hidden utility lines or
call the local utility company for assistance contact
with electric lines can lead to re or electrical shock
damaging a gas line can result in an explosion
penetrating a water pipe will cause property damage or
an electrical shock
Do not work materials containing asbestos asbestos
is considered carcinogenic
Dust from material such as paint containing lead some
wood species minerals and metal may be harmful
contact with or inhalation of the dust may cause allergic
reactions andor respiratory diseases to the operator or
bystanders wear a dust mask and work with a dust
extraction device when connectable
Certain kinds of dust are classied as carcinogenic
such as oak and beech dust especially in conjunction
with additives for wood conditioning wear a dust
mask and work with a dust extraction device
when connectable
Follow the dustrelated national requirements for the
materials you want to work with
Ensure that switch B 2 is in the middle locking position
before making any adjustments or changing accessories
as well as when carrying or storing the tool
CHARGINGBATTERIES
Charge battery only with the charger that is supplied with
the tool
Do not touch the contacts in the charger
Do not expose toolchargerbattery to rain
Do not charge battery in damp or wet environments
Store toolchargerbattery in locations where temperature
will not exceed C or drop below C
Do not use charger when damaged take it to one of the
ocially registered SKIL Service Stations for a safety
check
Do not use charger when cord or plug is damaged cord
or plug should be replaced immediately at one of the
ocially registered SKIL Service Stations
Do not use battery when damaged it should be replaced
immediately
Do not disassemble charger or battery
Do not attempt to recharge nonrechargeable batteries
with the charger
To Next Page
Loading...
Need help?
General
