Skil STZ6307 User Manual

6. Use the mounting holes of the zero clearance insert to drill four holes Ø1/8–9/64
inch (3.2–3.5 mm) in the supports for the insert plate as shown in Fig. 2.
Mounting
holes
Fig. 2
7. Use a Philips head screwdriver to secure the zero clearance insert in place with
the four (4) included #8x3/8” self-tapping mounting screws as shown in Fig. 3.
Mounting
screws
Fig. 3
8. Connect the saw to a power source.
9. Turn the saw on and slowly raise the blade as high as it will go until the blade
cuts completely through the insert to reach the rear slot opening (Fig. 4).
Rear slot opening
Fig. 4
10. Disconnect the saw from power source.
11. Level the zero clearance insert:
a. Thezeroclearanceinsertshouldbeush*withthesawtablesurface.
b. Place a straight edge (such as the metal ruler from a combination square)
across the saw table and the insert – the surfaces should be at the same
level (Fig. 5).
* Thefrontedgeoftheinsertmaybebelowthesawtablebythethicknessof
a piece of paper folded twice. Place the folded paper between the insert and
straightedgetocheck.Therearedgemaybeabovethesawtablebythe
same amount.
c. If adjustment is necessary, use a 2.5mm hex wrench (not included) to adjust
four (4) leveling screws (Fig. 5).
WARNING
This zero clearance insert is designed specifically for use only
with SKIL TS6307-00 table saw.
WARNING
Read the table saw manual for use of this accessory with the
saw.
NOTICE: This accessory is for 90° cuts only. Do not use it for bevel cuts.
1. Disconnect the saw from power source.
2. Removethebarrierguardassembly,theanti-kickbackdevice,andtheexisting
table insert from the saw as instructed in the saw manual.
3. Placetherivingknifetoitslowestpositionandlockitinplace.
WARNING
The riving knife should be adjusted to and locked in the lowest
position when making the initial cut in the zero clearance insert.
4. Lower the blade completely below the table surface.
5. Place the zero clearance insert in the table opening as shown in Fig. 1.
Fig. 1
Zero
clearance
insert
Owner’sManual
Model: STZ6307
Zero Clearance Insert
Rear edge
Front edge
Leveling
screws
Fig. 5
12.Removethezeroclearanceinsert.Raisetherivingknifeandreattachthebarrier
guardassemblyandtheanti-kickbackdeviceasinstructedinthesawmanual.
13. Reinstall the zero clearance insert.
WARNING
An improperly leveled insert can result in binding which could
result in personal injury. Verify adjustments by making a dry cut
before using the saw.
WARNING
Never operate the saw without the proper insert in place. Use the
saw insert when sawing and the dado insert when using a dado
set.
For Customer Service
Pour le service à la clientèle
Servicio al cliente
1-877-SKIL-999
OR
www.skil.com
© Chervon North America, 1203 E. Warrenville Rd, Naperville, IL 60563.

Skil STZ6307 Specifications

General

Brand	Skil
Model	STZ6307
Category	Tools
Language	English

Summary

Skil Zero Clearance Insert Installation Guide

Initial Warnings and Preparation

Covers initial warnings, disconnecting power, removing existing insert, and setting the riving knife.

Mounting the Zero Clearance Insert

Details drilling mounting holes and using screws to attach the insert plate to the saw.

Blade Alignment and Initial Cut

Instructions for connecting power and raising the blade for the first cut through the insert.

Leveling the Zero Clearance Insert

Steps to ensure the insert is flush with the table using leveling screws for proper alignment.

Final Installation and Safety Precautions

Reinstalling components and critical safety warnings regarding proper use and leveling.