SkyWave IDP 800 Series User Manual (English)

To Next Page

IDP 800 Terminal Series

Hardware Guide

T209, Version 01

The electronic version of this document allows

you to use the built-in Hyperlinks and

bookmarks when using Adobe Reader

Mar 2013

Legal Notice2
- Table of Contents3
Contact Information2
List of Figures6
Preface9
- Purpose9
- Audience9
- Errata Sheet9
- Notation9
- Reference9
- Battery Safety Warnings9
- Product Safety Datasheets10
- Safety Disclaimer10
- Safety Precautions10
- Installation Warning11
- Installer Responsibility11
- Limited Liability11
- Warranty12
- User Serviceable Parts12
1 Product Overview13
- Overview of the Messaging System13
- Figure 1 IDP-800 with Battery Compartment13
- Terminals14
- Figure 2 Skywave's Isatdata Pro Network14
- Remote Antennas15
- Figure 3 Remote Standard Antenna Side Connector15
- Figure 4 Remote Standard Antenna Bottom Connector15
- Figure 5 Remote Low Elevation Antenna Side Connector15
- Terminal Key Features and Benefits16
- Pass-Through Mode16
- Operating Modes17
2 Compliance21
3 Specifications23
- Temperature23
  - Terminal Temperature23
  - Battery Temperature23
- Electrical23
  - External Voltage Input23
  - Power Consumption24
  - Power off Controls25
  - Table 7 Power Consumption Scenario25
  - Power Input Options26
  - Figure 7 Magnet Fob on the Magnet Sensor26
  - Load Dump Circuitry27
  - Fuse27
  - In-Rush Current27
  - Table 8 Power Input Options27
  - Reverse Polarity28
  - Power Connector28
    - Connector Pin-Out28
  - Input/Output28
- RF Connector31
  - Antenna Cut Detection31
- Pass-Through Mode31
- Figure 9 Pass-Through Mode Signals31
- Table 13 RF Connector31
- Table 14 Pass-Through Mode Power31
- Serial Interfaces32
- Table 15 Pass-Through Mode Timing Specifications32
- Table 16 Pass-Through Mode Power Consumption32
- RF Specifications33
  - Frequency33
  - Terminal with Integrated Antenna33
  - Remote Standard Antenna33
  - Remote Low Elevation Antenna33
- Gps34
- Table 17 GPS Specifications34
- Internal Battery35
  - Battery Type35
  - Table 18 Approved Skywave Batteries35
  - Battery Type Identification36
  - Battery Lid Matching36
  - Figure 10 Rechargeable (Nimh) Battery Label36
  - Figure 11 Non-Rechargeable36
  - Figure 12 Non-Rechargeable Terminal36
  - Charger37
  - Charging Stages39
  - Table 19 Charger Initiation Parameters39
  - Table 20 Battery Temperature Specifications39
- Accelerometer40
- Table 21 Charging Stage Specifications40
- Figure 15 Accelerometer Axis41
- Table 22 Accelerometer Specification41
- Non-Volatile Storage42
- Environmental42
- Mechanical43
  - Terminal44
  - Figure 16 IDP-800 Top View Enclosure Dimensions44
  - Figure 17 IDP-800 Side View Enclosure Dimensions44
  - Figure 18 IDP-800 Connector View Enclosure Dimensions44
  - Remote Antenna45
  - Figure 19 Remote Standard and Low Elevation Antenna - Bottom View (MM)45
  - Figure 20 Remote Standard Antenna Height Dimensions45
  - Figure 21 Remote Low Elevation Antenna Height Dimensions (MM)46
- Led47
- Table 23 LED Flash Rates47
4 Installation49
- Getting Started49
- Prepare for the Installation49
- Determine a Suitable Mounting Location52
  - Remote Antenna Mounting Guidelines (Optional)53
- Identify the Fuse Panel Location (Optional)54
- Prepare the Batteries54
- Mount the Terminal59
- Mount the Remote Antenna (Optional)61
- Route the Main Cable (Optional)67
- Apply Power70
- Register the Terminal71
- Cleaning Instructions72
5 Troubleshooting the Terminal73
- Terminal Does Not Register or Report73
- Shipping Terminals Back to Skywave73
APPENDIX A Order Part Numbers75
- Table 24 Order Part Numbers75
APPENDIX B Activation Information76
APPENDIX C Replacing Lithium Batteries77
- Figure 48 Battery Cover - Sides77
- Figure 49 Battery Cover - Areas to Avoid78
APPENDIX D Reinstalling or Replacing a Terminal79
APPENDIX E Replacing a Battery Gasket80
- Figure 50 Gasket Hook and Loop Features80
- Figure 51 Fit Loops over the Hooks81
APPENDIX Fvhb Rail Bracket Installation82
- Installation Guidelines82
- Attach the Bracket and Prepare the Surface82
- Figure 52 VHB Rail Bracket and Lanyard83
- Figure 53 Lanyard Attached to Terminal83
- Figure 54 Assembled Terminal with VHB Rail Bracket and Lanyard84
- Select a Mount Option85
- Figure 55 Installation Location for VHB Rail Bracket and Lanyard85
- Figure 56 Rivet Hole Locations88
APPENDIX G IDP 800 Series Blunt Cut Cable89
- Figure 57 IDP 800 Series Blunt Cut Cable89
- Figure 58 Face View of IDP 800 Series Blunt Cut Cable Connector90
- Figure 59 Raw Cable Details90
- Table 25 IDP 800 Series Mating Blunt-Cut Cable Color Code90
APPENDIX H Cable Assembly Instructions91
- Required Tools and Materials91
- Cable Assembly Steps91
- Figure 60 Basic Connector Parts for Soldering Configuration91
- Figure 61 Recommended Stripping Length92
- Figure 62 Cable with Sealing Nut and a Back Shell92
- Figure 63 O-Ring92
- Figure 64 Red Gasket93
- Figure 65 Wires and Solder Cups93
- Figure 66 O-Ring over Connector Body93
- Figure 67 Silicone in the Connector94
- Figure 68 Silicone in the Grommet94
- Figure 69 Cable Exit Area94
- Figure 70 Assembled Sealing Nut95
APPENDIX Iidp 800 Series to IDP 600 Series Adaptor Cable96
- Figure 71 IDP 800 Series to IDP 600 Series Adaptor Cable96
- Figure 72 IDP 800 Series Mating Connector End Pin-Out97
- Figure 73 IDP 600 Series Connector End Pin-Out97
- Table 26 Cable Connector Pin-Out97
Revision History99
Acronyms/Glossary100
Index101

Need help?

Do you have a question about the SkyWave IDP 800 Series and is the answer not in the manual?

SkyWave IDP 800 Series Specifications

General

Category	Touch Terminals
Manufacturer	SkyWave Mobile Communications
Satellite Service	Inmarsat IsatData Pro
Ports	USB, Serial
Interfaces	RS-232, RS-485
Power Input	9-36 VDC
Touch Screen	Resistive
Connectivity	Bluetooth
Communication	Satellite, Cellular
GPS	Integrated

Related product manuals

SkyWave IDP 800 Series User Manual

Table of Contents

SkyWave IDP 800 Series Specifications

Related product manuals