What to do if SMA SUNNY MINI CENTRAL 9000TL shows EEPROM dBh error?
If your SMA Inverter displays 'EEPROM dBh', the EEPROM data is defective, and the inverter has shut down because the data loss has disabled important functions. Contact the SMA Serviceline.
How to fix SMA Inverter showing 'Check L-N-PE'?
If your SMA Inverter displays 'Check L-N-PE', it means L and N are swapped on the AC connection or PE is not connected. Make sure that the AC cable is correctly connected.
Why is my SMA SUNNY MINI CENTRAL 9000TL Inverter derating?
The SMA Inverter might be derating (reducing its power output) due to overheating. In this case, clean the fans. Alternatively, derating can occur if the DC input current exceeds the inverter's maximum input current; ensure that the PV plant is designed correctly.
What does ACVtgRPro mean on my SMA Inverter?
If your SMA Inverter displays 'ACVtgRPro', the ten-minute average mains voltage is no longer within the permissible range. Check that the mains voltage at the termination point of the inverter is permanently in the permissible range. If the mains voltage is 253 V or higher, contact the network operator.
What does 'Earthfault' mean on my SMA SUNNY MINI CENTRAL 9000TL and how to fix it?
If your SMA Inverter displays 'Earthfault', it indicates that the electrical insulation between the PV plant and earth is defective. Make sure that the PV plant is insulated correctly.
How to solve Check L-N-PE error on SMA Inverter?
The 'Check L-N-PE' error on your SMA Inverter indicates that the L and N are swapped at the AC connection or PE is not connected. Check the AC connection.
What does SD-DI-Wandler error mean on SMA SUNNY MINI CENTRAL 9000TL?
The 'SD-DI-Wandler' error on your SMA Inverter indicates an insulation fault on the DC side. Check the plant insulation and inspect for ground faults.
What does Imax mean on SMA Inverter?
The 'Imax' message on your SMA Inverter indicates overcurrent on the AC side, meaning the current in the AC grid is higher than specified. Check the system design and grid conditions.
How to fix PV overvoltage on SMA SUNNY MINI CENTRAL 9000TL?
If your SMA Inverter displays 'PV-Overvoltage' and instructs you to disconnect DC, it indicates an overvoltage at the DC input, which can damage the inverter. Immediately disconnect the inverter from the grid by: 1. Turning off the line circuit breaker. 2. Removing the Electronic Solar Switch. 3. Disconnecting all the DC plug connectors. Then, check the DC voltage. If it exceeds the maximum input voltage, inspect the plant design or contact the PV generator installer. If the voltage is within the limit, reconnect the inverter. If the message reappears, disconnect the inverter and contact the SMA Serviceline.
What causes damage to the SMA Inverter due to moisture and dust intrusion?
Damage to the SMA Inverter from moisture and dust intrusion can occur if the ESS is not plugged in or incorrectly plugged in during operation. Always plug in the ESS until it is flush with the enclosure and ensure that the gap between the ESS and the enclosure is no more than 1 mm.
General| Model | Sunny Mini Central 9000TL |
|---|---|
| Rated Output Power | 9000 W |
| Max. Input Voltage | 1000 V |
| Topology | Transformerless |
| Max. Apparent AC Power | 9000 VA |
| Number of MPP Trackers | 2 |
| Frequency Range | 50 Hz / 60 Hz |
| Protection Class | IP65 |
| Operating Temperature Range | -25 °C to +60 °C |
| Nominal AC Voltage | 400 V |
| AC Voltage Range | 180 V - 280 V |
| Max. Output Current | 13 A |
| MPPT Range | 200 V - 800 V |
To Next Page
