Snapper 7800849 Parts Manual

Not for
Reproduction
Footnotes:
Manual No.
710616722" STEEL DECK WALK BEHIND
SERIES 20
13
Drive System, Self Propelle
d
Part No Descri
p
tionItem Qty
1 1753983YP 1 SCREW, 5/16-18 x 5/8 Truss Head Torx
2 7090391SM 1 WASHER, 5/16, Internal Lock, Zinc/Clear (Was 80003683)
3 7034179BMYP 1 LINK, Differential, Commercial
4 703940 1 WASHER, 0.445 ID X 0.780 OD X 0.025 Thk, Wave, ZC/CL (Was 7011724 or 80005390)
5 7012354YP 1 BELT, Poly-V
6 703127 1 NUT, 1/4-20, G5 Zinc/Clear (Was 7090063, 7091576 or 80003586)
7 703462 2 WASHER, 1/4 Internal Tooth Lock, YZ (Was 7090053 or 80004414)
8 7012616YP 1 SUPPORT, Foot Guard
9 703978 1 BOLT, 1/4-20 X 1/2, Carriage, GR5 YZ (Was 7090005, 7091604 or 80004564)
10 7029008YP 1 GUARD, Rear Foot, 21”
11 704009 1 RING, Split, .68 x .93 x .44 (Black) (Was 7023791 or 80005645)
12 703458 1 NUT, 3/8-24 Hex Center Lock, GR B, YZ (Was 7090289 or 80004409)
13 B4300GS 2 SCREW, 1/4-20 X .500, Hex HD, Self-Tap, Zinc/Clear (Was 1925003, 704130, 7090539,
7091122, 720041 & 80002738)
14 7031809YP 1 HOLDER, Bearing (Outer Half), ZC/CL
15 704008 1 O-RING, 1.0 ID X 1.25 OD X 0.125 Thk (Was 7011025 or 80005646)
16 7028014YP 1 BALL BEARING, Spherical O.D., .38 I.D.
17 7031873YP 1 HOLDER, Bearing (Inner Half)
18 703946 1 WASHER, .390 ID X .720 OD X .054 Thk, Flat, ZC/CL (Was 7012316 or 80005532)
19 7019383YP 1 PULLEY, Poly-V, 2.0” OD, Steel
20 703895 2 NUT, 3/8-24, Hex, GR 5, Zinc/Clear (Was 7091630 or 80004865)
21 703930 3 WASHER, 3/8” Internal Tooth Lock,Type A, ZC/CL (Was 7090390 or 80005380)
22 703836 1 STUD, 3/8-24 X 2.38, Single End, ZC/CL (Was 7012111 or 80004419)
23 7012126YP 1 SPRING, Idler Torsion
24 703828 1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap, Grade 5, CZ/CL (Was 7091025 or 80004836)
25 7012124YP 1 PULLEY, Flat Idler, .25 ID, 2.25 OD
26 703972 1 NUT, 1/4-28 Hex Top Lock, GR 5, BZ (Was 7090303 or 80005377)
27 7012122YP 1 SPRING, Clutch
28 331613MA 1 PIN, 3/32 X 3/4, GR5, Cotter, Zinc/Clear (Was 1918447, 703312, 7090555, 7091597 or
80002736)
29 7072284YP 1 SHAFT, Hex (3/8-24 thread, one end)
30 704060 7 SCREW, #10-24 x 1/2” Hex Washer Self-Tap, Torx, ZC/CL (Was 7090913 or 80005972)
31 7031013YP 1 PLATE, Driven Tire Side
32 704059 1 Disc, Rubber Driven, 3” ID (Was 7010927, 7023364 or 80005971)
33 703837 1 STUD, 3/8-24 X 4.5, Plate, ZC/CL (Was 7012125 or 80004420)
34 704061 4 SCREW, #10-32 X 1/4,Hex Washer, Self-Tap, ZC/CL (Was 7090981 or 80005973)
35 7029027YP 1 BEARING, 3/4” ID, Ball, Commercial
36 7300977BMYP 1 THRUST PLATE, Short, Black
37 703975 1 RETAINING RING, 3/4” ID, ZC/CL (Was 7010746 or 80005391)
38 703590 1 WASHER, 3/8 (.406 X .816 X .65), Flat, Zinc/Clear (Was 7090122, 71072MA or 80003536)
39 703461 2 NUT, 1/4-28 Hex, GR5, Zinc/Clear (Was 7090095 or 80004412)
40 703332 2 WASHER, 1/4, Flat, GR5 Zinc/Clear (Was 1921319, 7022473, 5025154, 7091294) or 80002742)
41 7015753YP 2 BALL JOINT, 1/4-28
42 7074145YP 1 LINK, Transfer (1/4-28 thread)
43 703464 1 PIN, 1/16 X 0.50 Cotter, GR 5 Zinc/Clear (Was 1501125MA, 579493MA, 7090673, 7091629,
724605 or 80003540)

Snapper 7800849 Specifications

General

Brand	Snapper
Model	7800849
Category	Lawn Mower
Language	English