Sniper Automotive SNIPER X2 User Manual

-
SNIPER X2 VEHICLE SECURITY SYSTEM
Installation Manual
1. INSTALLATION
1.1. Arm Condition Memory
If power to the alarm is removed it will remain in the same status when power it restored.
1.2. Immobiliser Relay Wiring
The system offers two ways of wiring the immobiliser as shown below.
When wired for Normally Open the immobiliser relay is switched on when the alarm is disarmed (fail secure). When wired as Normally
Closed the relay is on when the alarm is armed (fail safe).
Wiring Diagram - Immobiliser Relay NO & NC
Normally Closed Immobiliser Connection (Fail Safe)
87a - Normally Closed
87 - Normally Open
Off
Acc
On
Start
86
85
87
87a
30
To +12V DC or Acc.
W2-8
fig. 2
Normally Open Immobiliser Connection (Fail Secure)
87a - Normally Closed
87 - Normally Open
Off
Acc
On
Start
86
85
87
87a
30
To Acc.
W2-7
fig. 1
1.3. Programming New Remote Controls
The included remote controls have been programmed to the system in the factory. Follow the procedure below to program a new
remote control to the system:
- Turn the ignition on with the system disarmed.
- Within 10 seconds, press valet switch 6 times.
- The siren sounds for 2 sec. to confirm the system is now in code learning mode.
- Within 10 sec., press any button of 1
st
remote control
The siren will sound for 1 sec. and hazard lights flash twice to confirm the 1
st
remote has been programmed to the system and all
the previous codes in the system will be erased entirely.
- Within 10 sec., repeat for the 2
nd
remote control and again for 3
rd
and 4
th
remotes as applicable.
* Up to 4 remotes can be programmed to the system
* The system will leave the code learning mode after programming 4 remotes to the system and the siren will sound for 2
seconds
to confirm.
* If no buttons are pressed within 10 seconds, the system will leave the learning code mode and the siren will sound for 2 seconds
to confirm.
* The system will leave the code learning mode if the ignition is turned off at any time and the siren will sound for 2 seconds to
confirm.

Sniper Automotive SNIPER X2 Specifications

General

Brand	Sniper Automotive
Model	SNIPER X2
Category	Car Alarm
Language	English

Summary

Installation

Arm Condition Memory

System retains its status (armed/disarmed) when power is restored.

Immobiliser Relay Wiring

Wiring options for normally open (fail-secure) and normally closed (fail-safe) immobiliser relay connections.

Programming New Remote Controls

Procedure to program up to four new remote controls to the system.

Bypass Input

Ground input for external modules to bypass ignition and shock sensor.

Start Output

Pulse output to activate or deactivate an external engine start module.

Interior Light Supervision

Controls interior light activation when disarming or during alarm.

Program Optional Features

Steps to enter programming mode and select optional features.

Optional Programmable Features

Table listing programmable features and their available settings.

Override Code Programming

Procedure to program the system's override code.

Explanation of the Optional Features

Detailed explanations for various programmable system features.

Auto. Rearming

System automatically re-arms after 30 seconds if no doors are opened.

AED, Auto Engine Disable

Disables engine after ignition off and door closure.

Door Open Alerts

Hazard lights flash when a door is opened.

Total/Comfort Closure

Automatically closes windows when arming the system.

Disarm with Boot Release

Disarms system when operating boot release.

Anti-hijacking Countdown

System enters anti-hijacking mode after a countdown.

Activate Anti-hijacking Countdown

Sets how anti-hijacking countdown is initiated (normal/brake).

Anti-hijacking by Remotes

Activates anti-hijacking by pressing remote button #1.

Anti-hijacking by Ignition+Door

Activates anti-hijacking by opening/closing a door.

Override Code

Procedure to change and operate the override code.

Hazard Lights Output

Configures hazard light output for pulse or continuous.