What to do if I get warnings due to incorrect system design in Solar MD Camera Accessories?
If your Solar MD Camera Accessories system design isn't correct, consider adding an additional battery or decreasing the charging/discharging current from your inverter, rectifier, or load.
How to fix a CANBUS warning on Solar MD Camera Accessories?
If you encounter a CANBUS warning with your Solar MD Camera Accessories, it might be due to an open CANBUS line or a single CANBUS resistor not being terminated. First, check if at least two nodes are connected on the line with the same transmission speed. Then, verify if a single resistor is terminated via the jumper, located at the top left of the CAN LEDs.
What to do if the maximum charge/discharge current is achieved on Solar MD Camera Accessories?
If the absolute maximum charge or discharge current has been achieved, the BMS will restart automatically. For further assistance, please contact the support team or an approved installer for your Solar MD Camera Accessories.
What to do if the BMS has been shut down manually or remotely in Solar MD Camera Accessories?
If the BMS for your Solar MD Camera Accessories has been shut down manually or remotely, switch it back on.
What to do if BMS is set for the wrong number of cells in series in Solar MD SS4074-01 Camera Accessories?
If the BMS for your Solar MD Camera Accessories is set for a different number of cells in series than actually installed, contact your installer or the Solar MD support team.
How to correct battery position error in Solar MD SS4074-01 Camera Accessories?
If the Solar MD Camera Accessories battery is not installed in an upright position, install it in the correct, upright position.
What to do if BMS is ready to switch on after deep discharge/charge in Solar MD SS4074-01?
If the BMS is ready to switch on after deep discharge/charge of your Solar MD Camera Accessories, connect a charger or load to the battery.
What happens if the battery cell voltage is too high in Solar MD Camera Accessories?
If the battery cell voltage is way too high in your Solar MD Camera Accessories, the BMS will restart automatically after a pending awake condition.
Details the SS4074-01 battery solution, its size, paralleling capability, and voltage ratings.
Verifies accuracy of specifications and reserves the right for product improvements.
Instructions for reporting inaccuracies or omissions in the manual.
States copyright ownership by Solar MD (Pty) Ltd.
Important instructions, warnings, and cautions for using the SS4074-01 battery.
Detailed technical specifications including chemistry, capacity, voltage, power, and dimensions.
Guidelines for mounting the battery bracket and installation screws, including tilt angle limits.
Details the installation of single or dual cable exit cover plates using M5x6 bolts.
Step-by-step guide for electrical connections, starting with the ON/OFF switch position.
Diagram labeling key components on the BMS board for electrical installation.
Precautions and cable sizing guidelines for connecting external devices to the battery.
Instructions for connecting negative and positive cables and ensuring tight connections.
Details CANBUS connection specifications, wire type, and galvanic isolation.
Diagram showing BMS-EM units connected to the CANBUS.
Step-by-step guide for commissioning the battery system, including checks and switch operations.
Important note on current distribution when commissioning multiple batteries.
Introduces the multipurpose button and its extended functionality with BMS-EM.
Lists the 6 predefined functions accessible via the button and LED feedback.
Describes how the button's illumination indicates status and user choices (off, capacity, capacity with direction, fixed color with direction).
Explains how the board uses LEDs to display general warnings and errors.
Diagram showing LED indicators for warnings and errors.
Lists warning codes, their LED patterns, and causes.
Lists error codes, their LED patterns, and causes.
Continues listing error codes, their LED patterns, and causes.
Explains CANBUS warnings displayed by the Orange WARN LED using pulse counting.
Identifies CANBUS termination resistor and WARN LED locations.
Table correlating codes, causes, and solutions for warnings and errors.
Troubleshooting steps for specific warning codes (1-2, 3-4, 5-6, 29-30).
Troubleshooting steps for specific error codes (5-7, 15-17, 18-19, 21, 22, 23, 24, 25-31).
Troubleshooting steps for CANBUS warning code 1.
Table of recommended voltage setpoints for 24V and 48V systems without communication.
Guidance on checking equalization functions and voltage differences for system compatibility.
General| Brand | Solar MD |
|---|---|
| Model | SS4074-01 |
| Category | Camera Accessories |
| Language | English |
To Next Page