Sony HT-X9000F User Manual

SERVICE MANUAL
Sony Video & Sound Products Inc.
Amplier section
(X9000F: US)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(FTC)
Front L + Front R:
With 4ohms loads, both channels
driven, from 200 - 20,000Hz; rated
35W per channel minimum RMS
power, with no more than 1% total
harmonic distortion from 250mW to
rated output.
POWER OUTPUT (reference)
Front L/Front R speaker blocks: 100W
(per channel at 4ohms, 1kHz)
(X9000F: CND/XF9000: AEP, UK)
POWER OUTPUT (rated)
Front L + Front R: 60W + 60W
(at 4ohms, 1kHz, 1% THD)
POWER OUTPUT (reference)
Front L/Front R speaker blocks: 100W
(per channel at 4ohms, 1kHz)
Inputs
HDMI IN*
ANALOG IN
TV IN (OPT)
Outputs
HDMI OUT (TV (ARC))*
*HDMI IN and HDMI OUT (TV (ARC)) jacks
support HDCP 2.2 protocol. HDCP 2.2 is
newly enhanced copyright protection
technology that is used to protect
content such as 4K movies.
HDMI Section
Connector
Type A (19pin)
USB section
(USB) port:
Type A (For connecting USB memory)
BLUETOOTH section
Communication system
BLUETOOTH Specication version 4.2
Output
BLUETOOTH Specication Power
Class1
Maximum communication range
Line of sight approx. 30m
1)
Maximum number of devices to be
registered
9 devices
Frequency band
2.4 GHz band (2.4GHz - 2.4835GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible BLUETOOTH proles
2)
A2DP (Advanced Audio Distribution
Prole)
AVRCP (Audio Video Remote Control
Prole)
Supported Codecs
3)
SBC
4)
, AAC
5)
Transmission range (A2DP)
20 Hz - 20,000 Hz (Sampling frequency
32kHz, 44.1kHz, 48kHz)
1)
The actual range will vary depending on
factors such as obstacles between
devices, magnetic elds around a
microwave oven, static electricity,
cordless phone use, reception
sensitivity, the operating system,
software applications, etc.
2)
BLUETOOTH standard proles indicate
the purpose of BLUETOOTH
communication between devices.
3)
Codec: Audio signal compression and
conversion format
4)
Abbreviation for Subband Codec
5)
Abbreviation for Advanced Audio
Coding
Front L/Front R speaker block section
Speaker system
Full Range speaker system, Acoustic
suspension
Speaker
40mm × 100mm (1 5/8 in. × 4 in) cone
type
General
Power requirements
120 V AC, 60 Hz (X9000F: US, CND)
Power consumption
On: 38W
[Bluetooth Standby] - [On]: Less than
2W
[Bluetooth Standby] - [O]: Less than
0.5W
Dimensions* (approx.) (w/h/d)
930mm × 58mm × 85mm (36 5/8 in ×
2 3/8 in × 3 3/8 in)
*Not including projection portion
Mass (approx.)
2.5kg (5 33/64 lb)
Frequency band
2.4GHz (2.4000GHz - 2.4835GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Design and specications are subject to
change without notice.
Wireless Transmitter/
Receiver Section
220 V - 240 V AC, 50 Hz/60 Hz
(XF9000: AEP, UK)
What’s in the Box
t#BS4QFBLFS
t4VCXPPGFS
t3FNPUFDPOUSPM
t3TJ[F"""CBUUFSZ
t)%.*DBCMFTVQQPSUTUIFTQFDJöDBUJPO
equal to Premium High Speed HDMI
Cable with Ethernet) (1) (X9000F: US, CND)
t0QUJDBMEJHJUBMDBCMF9'"&16,
t8"--.06/55&.1-"5&
t4UBSUVQ(VJEF
t0QFSBUJOH*OTUSVDUJPOT
HT-X9000F/XF9000
SA-X9000F/XF9000
SPECIFICATIONS
HT-X9000F/XF9000
SOUND BAR
SA-X9000F/XF9000
ACTIVE SPEAKER SYSTEM
9-896-483-01
2018A33-1
©
2018.01
US Model
Canadian Model
HT-X9000F/SA-X9000F
AEP Model
UK Model
HT-XF9000/SA-XF9000
Ver. 1.0 2018.01
• All of the units included in the HT-X9000F
(SA-X9000F/SA-WX9000F/Remote
control) or HT-XF9000 (SA-XF9000/SA-
WXF9000/Remote control) are required
to confi rming operation of SA-X9000F/
XF9000. Check in advance that you have
all of the units.
COMPONENT MODEL NAME
HT-X9000F HT-XF9000
Bar Speaker (Active Speaker System) SA-X9000F SA-XF9000
Subwoofer (Active Subwoofer) SA-WX9000F SA-WXF9000
• Please refer to service manual separately issued for Subwoofer.
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Photo: SA-X9000F

Sony HT-X9000F Specifications

General

Total Power Output	300W
Sound Technology	Dolby Atmos, DTS:X
Subwoofer	Wireless
HDMI Inputs	1
HDMI Outputs	1
Dimensions (Soundbar)	930 x 58 x 85 mm
Dimensions (Subwoofer)	190 x 382 x 387 mm
Weight (Soundbar)	2.5 kg
USB	Yes
Type	Soundbar
Connectivity	Bluetooth, USB

Summary

SERVICING NOTES

UNLEADED SOLDER

Information and precautions for using lead-free solder in repairs.

NOTE OF REPLACING THE FUSE

Safety precautions for replacing fuses, emphasizing disconnecting power.

DISCHARGE PROCESSING

Procedure for safely discharging capacitors to prevent electric shock.

MODEL IDENTIFICATION

How to identify unit models using part and destination codes.

SERIAL NUMBER WRITING WORK

Serial number writing procedure

Step-by-step guide for writing the serial number after main board replacement.

WIRELESS CONNECTION (LINK) WORK

Secure link method

Detailed steps to perform a secure wireless link between units.

Secure link cancellation method of bar speaker

Steps to cancel the secure link for the bar speaker.

SYSTEM MANAGEMENT AND MODES

RESETTING THE SYSTEM

Procedure to reset all unit settings to factory defaults.

Pre-Repair Confirmation Checks

Guidance on checking issues before attempting repairs.

Component Replacement Notes

Important notes for replacing specific boards and electrical parts.

MALFUNCTION PREVENTION OF THE BUTTON (TOUCH PANEL SWITCH)

Precautions to prevent touch panel malfunctions during operation checks.

DISASSEMBLY PROCEDURES

2-1. DISASSEMBLY FLOW

Overview of the disassembly sequence for the unit.

2-2. TOP/BOTTOM CABINET BLOCK-1

Procedure for disassembling the top and bottom cabinet sections.

2-15. MAIN BOARD-1

Procedure for removing the first part of the main board.

TEST MODE OPERATIONS

FACTORY INITIALIZE (Factory Settings)

Procedure to reset all unit settings to factory defaults.

USB UPDATE

Procedure for updating firmware using USB memory.

DEMO MODE

Procedure to enter and operate the demo mode.

DEMO MODE MANAGEMENT

DEMO RESET

Procedure to release the unit from demo mode.

COPY BUILT-IN DEMO CONTENTS

Procedure to overwrite demo content with USB data.

PANEL TEST AND SERVICE MODE

PANEL TEST

Procedure to check LED lighting states and key input functionality.

SERVICE MODE

How to enter and navigate the unit's service mode.

SERVICE MODE MENU DETAILS

5. Serial number Editor

Function to edit the unit's serial number.

TROUBLESHOOTING GUIDE

1. Protection mode is occurs after turning the power on.

Troubleshooting steps for protection mode activation.

2. The video and audio of HDMI is not outputted

Diagnostic steps for no HDMI video or audio output.

3. The sound is not outputted

Troubleshooting steps when no sound is produced.

4. Power is not turned on

Diagnostic flow for the unit not turning on.

5. The sound is not outputted of ARC

Troubleshooting steps for sound issues specifically with ARC connection.

6. The subwoofer is not linked

Troubleshooting steps when the subwoofer fails to link.

DIAGRAMS AND CIRCUIT ANALYSIS

5-1. BLOCK DIAGRAM - HDMI Section -

Block diagram illustrating the HDMI signal path and components.

5-2. BLOCK DIAGRAM - Main Section -

Block diagram showing the main processing and interface sections.

5-3. BLOCK DIAGRAM - AMP Section -

Block diagram detailing the audio amplifier section.

5-4. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section -

Block diagram of the panel interface and power supply circuits.

Waveforms and IC Block Diagrams

Visual representations of signal waveforms and functional block diagrams for key ICs.

PHYSICAL COMPONENT LAYOUT

Printed Wiring Board and Schematic Diagram Notes

General notes applicable to printed wiring and schematic diagrams.

Circuit Boards Location

Visual guide showing the physical location of major circuit boards.

EXPLODED VIEWS AND PARTS LIST

6-1. FOOT SECTION

Exploded view of the unit's foot section and associated parts.

6-2. TOP CABINET SECTION

Exploded view of the top cabinet section and its components.

6-3. BOTTOM CABINET SECTION

Exploded view of the bottom cabinet section and its parts.

6-4. MAIN BOARD SECTION

Exploded view showing the main board and related components.

6-5. SK1 AMP BOARD SECTION

Exploded view of the SK1 AMP board and its associated parts.

6-6. POWER BOARD SECTION

Exploded view of the power board and its components.

SECTION 7 ELECTRICAL PARTS LIST

Comprehensive list of electrical parts with their part numbers.

REVISION HISTORY

How to search for a contact point of signal lines or the like in DIAGRAMS SECTION

Guide on using PDF search to locate signal path contact points.