To Next Page
S
Stanley TerrySep 23, 2025
Why is No MAS-A100 found on the [Routing] tab of Dante Controller for Sony Microphone?
- JJoshua GouldSep 23, 2025
Connect the PC to the same subnet as the MAS-A100 units, and then use Dante Controller.
Why is No MAS-A100 found on the [Routing] tab of Dante Controller for Sony Microphone?
Connect the PC to the same subnet as the MAS-A100 units, and then use Dante Controller.
What to do if the Sony MAS-A100 Microphone Rec output is silent?
If the Rec output of your Sony Microphone is silent: * Check the routing on the [Routing] tab of Dante Controller to ensure the Dante audio is correctly routed. * Verify the MAS-A100 is not in Standby state. Look at the status lamp on the [Monitor] tab of MASM-1; if it's red (Standby), press the Power button to switch it to green (Active) or amber (Mute). * Ensure that the noise gate is not enabled. If it is set to [Low], [Middle], or [High], audio below a certain threshold will be attenuated. Set the noise gate to [Off].
What to do if Sony MAS-A100 units are not found after pressing the [Scan] button of MASM-1?
If the MAS-A100 units are not found after pressing the [Scan] button of MASM-1, it may be due to these reasons: * The MAS-A100 units might not be on the same segment (same layer 2 network). Use MASM-1 running on a PC connected only on the same segment (same layer 2 network) to which the MAS-A100 units are connected. * The firewall setting might not be set appropriately. Configure the firewall to allow communication using UDP port 42380. Alternatively, temporarily disable the firewall during MAS-A100 discovery.
What to do if the gain limit is lit in MASM-1 for Sony Microphone?
If the gain limit is lit in MASM-1 for your Sony Microphone, it indicates that the speech reinforcement level has reached or exceeded the limit to suppress audio feedback while maintaining audio quality. One gain limit lamp means the speech reinforcement level has reached the limit, while two lamps mean it exceeds the limit. If you need a larger speech reinforcement level, consider reviewing the MAS-A100 installation environment and recalibrating.
How to fix MAS-A100 Sony Microphone not starting?
If your Sony MAS-A100 microphone does not start, it could be due to these reasons: * The network cable may not be connected properly. Ensure the link LED on the network switch is lit and the cable is correctly connected. * The PoE power supply may not be working correctly. Check that the PoE LED on the network switch is lit. If not, verify the network cable is category 5e or higher and shorter than 100 m. Also, ensure the network switch is grounded correctly and that the PoE power budget is not exceeded when connecting multiple units or other PoE devices.
What to do if Sony MAS-A100 does not respond within a certain time?
Restart the MAS-A100. If the problem persists, check the network connection.
What does it mean when [Other error] is displayed in MASM-1 for Sony MAS-A100?
If '[Other error]' is displayed in MASM-1, it could mean: * The response of the MAS-A100 is temporarily not normal. Wait a while, and refresh the view in MASM-1. * The network transfer speed is too slow. Reduce the number of MAS-A100 units when updating the firmware of multiple units at the same time.
What to do if the gain limit is lit, even though the calibration rating is high for Sony Microphone?
If the gain limit is lit, even though the calibration rating is high, it could be due to the following reasons: * Calibration was not completed successfully. * The volume is too high. Reduce the volume.
What to do if the Dante routing is correct, but audio is not emitted from a Dante receiver with Sony Microphone?
If the Dante routing is correct, but audio is not emitted from a Dante receiver, there may be a problem with the clock of the Dante network. On the [Clock Status] tab, check that only one Dante device is configured as the “Master” for Primary V1 Multicast. If more than one Dante device is configured as “Master”, there is a problem with the clock of the Dante network.
Why is there no device shown on the [Device Info] tab of Dante Controller for Sony MAS-A100?
If no device is shown on the [Device Info] tab of Dante Controller for your Sony Microphone, check the following: * If a third-party firewall application is in use, configure the firewall settings separately. Refer to the Dante Controller user guide provided by Audinate Pty Ltd for specific details. * Ensure the network switch is set to not block the network port used by Dante. * Verify that the Dante devices are on the same segment (same layer 2 network) as the PC. Check the network connection.
General| Polar Pattern | Omnidirectional |
|---|---|
| Frequency Response | 20 Hz - 20 kHz |
| Sampling Rate | 48 kHz |
| Bit Depth | 24-bit |
| Sensitivity | -35 dB |
| Connector | RJ45 |
| Power | PoE (Power over Ethernet) |
| Number of Channels | 1-channel |
