Stereo
Headphones
立体声耳机
MDR-AS35W
©2009 Sony Corporation Printed in Thailand
索尼公司 泰国印刷
4-169-972-31(1)
Operating Instructions
使用说明书
English
Stereo Headphones
Features
Lightweight vertical in-the-ear type design
Compact folding design with flexible headband
Powerful bass sound is provided by bass booster
Moisture Guard Mechanism pulls sweat away from ear canal (see fig.
)
Splash proof *
* The product’s functions will not be affected with exposure to some rain or drops of
water.
Wearing the headphones (see fig. )
1 Adjust the length of the headband for a comfortable fit.
2 Wear the headband on your head, and insert the earpiece marked in your
right ear and the one marked in your left ear.
There is a tactile dot on the unit marked to distinguish the left side.
How to re-attach the cord to the clip
(see fig. )
1 Hold the clip closed, and pull up the lever on the clip just a little.
2 Put the cord into the groove under the lever.
Notes
If you pull up the lever on the clip without holding the clip closed, or holding the clip
closed but opening the lever too much, you cannot put the cord into the groove under
the lever.
Do not catch the cord on the projection of the clip or do not wedge it into the groove.
It may damage the wires of the cord.
How to carry the headphones
1 Pull up the headband completely (see fig. -).
2 Pull up the cord slider until the and earpieces touch (see fig. -).
3 Fold the headband (see fig. -).
4 Insert the headphones into the storage space behind of the case (see fig. -
).
5 Wrap the cord around the hub (see fig. -), and insert the stereo mini
plug and excess cord in the hub compartment (see fig. -).
6 Close the cover of the hub compartment (see fig. -).
Note
Do not twist the cord tightly when wrapping around the center hub, or do not pinch
the cord when closing the lid. It may damage the wires of the cord.
The hinges may be slightly deformed upon removal from the case; however, this is not
a defect.
When inserting the headphones in the case, paraffin oil may seep out from the hinges.
This is harmless, and not a defect.
Specifications
Type: Open air, dynamic
Driver unit: 13.5 mm, dome type (CCAW adopted)
Power handling capacity: 50 mW (IEC*)
Impedance: 16 Ω at 1 kHz
Sensitivity: 104 dB/mW
Frequency response: 18 - 22,000 Hz
Cord: Approx. 0.6 m
Plug: Gold plated stereo mini plug
Mass: Approx. 17 g without cord
Supplied accessories
Carrying case (1)
Extension cord (0.6 m) (1)
Clip (1)
Operating Instructions (1)
* IEC = International Electrotechnical Commission
Design and specifications are subject to change without notice.
Precautions
Do not wash the headphones.
Though this headphones is water resistant design, avoid exposing the headphones to
excessive water or sweat. Water or sweat entering the headphones may damage them.
If the sound from the headphones becomes low or stops, leave the headphones to dry
out.
Listening with headphones at high volume may affect your hearing. For traffic safety,
do not use while driving or cycling.
Do not subject the headphones to excessive shock.
Handle the driver units carefully.
Do not leave the stereo headphones in a location subject to direct sunlight, heat or
moisture. It may break the headphones.
Clean the headphones with a soft dry cloth. Do not blow on the units when cleaning.
Do not allow the plug to become dirty, otherwise the sound may deteriorate.
Do not detach the earpiece. It may break the headphones.
Note on static electricity
During dry weather, you may experience mild pain in your ears. This is not by
malfunction of the headphones, but is due to static electricity accumulated in your body.
It is reduced by wearing clothes made of natural materials that do not generate static
electricity so easily.
Extension cord (supplied)Stereo mini plug
To Next Page
Need help?
General
